Panasonic S-3650PF3E Скачать руководство пользователя страница 281

Страница: 281 / 321

Item code

Item

Setting data

No.

Description

Automatic drain pump

operation

0000

No forced operation

0001

Forced operation for 1 minute

0060

Continuous operation

Ventilation fan operation

0000

None

0001

Ventilation fan operated by remote controller.

Wired remote controller

sensor

0000

Not used. (Body sensor is used.)

0001

Remote control sensor is used.

“Operation change control in

progress” display

0000

Normal (displayed)

0001

Not displayed

OFF reminder function for

when weekly timer is used

0000

None

0001

Only stop time setting is enabled.

Heat exchanger temperature

for cold air discharge

(Heat exchanger control

point for control to prevent

cold air)

-001

Control temperature -1°C

0000

Control temperature 0°C

0025

Control temperature 25°C

0026

Control temperature 26°C

Fan output switching

0000

Output linked with fan. (ON when indoor unit fan is operating.)

0001

Fan mode operation output

Drain pump delayed stop

time

0000

No delayed stop

0001

1 minute delayed stop

0002

2 minutes delayed stop

0058

58 minutes delayed stop

0059

59 minutes delayed stop

0060

60 minutes delayed stop

Humidifier setting

0000

Humidifier output OFF. Drain pump stopped.

0001

Humidifier output ON. Drain pump operates.

0002

Humidifier output ON. Drain pump operates for 1 minute when
total humidifier operating time reaches 60 minutes.

0003

Humidifier output ON. Drain pump stopped.

Flap operation mode

0000

Standard setting

0001

Draft reduction mode (Flap lower-limit position is shifted
upwards.)

Flap swing mode

0000

Smudging reduction mode (Flap swing upper-limit position is
shifted downwards.)

0001

Normal mode

0002

Draft reduction mode (Flap swing lower-limit position is shifted
upwards.)

7-8

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 8

20/01/28 11:22:20

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды