Panasonic S-3650PF3E Скачать руководство пользователя страница 298

Страница: 298 / 321

Indicator lamps

When an error occurs, one of the

lamps flashes. When an indicator

lamp is flashing, see

“8-2-1-18. Troubleshooting”.

CZ-RWRC3

Front side

Rear side

1 2 3 4

1
2
3

ADDRESS 1

ADDRESS 2

ADDRESS 3

REM SUB/MAIN

CZ-RWRU3

CZ-RWRU3W

3 4 5

1. Receiver

Receives the signal sent from the
remote controller.

Lights up when the unit is operating.

2. Emergency

operation button

See page 8-2-1-9.

The lamp in the HEAT mode lights
up at the following times: during
the startup, during the thermostat
operation, and during the
defrosting.

5. STANDBY lamp

3. OPERATION lamp

Lights up when the timer is set.

4. TIMER lamp

See the section “8-2-1-9. Pairing

Addresses”

7. Address switch

6. FILTER lamp

This lamp is for notifying you when
the filter needs to be cleaned.

RECEIVER

Screen display

13 14 15

Appears when ECONAVI is being

set to ON.

Indicates the set temperature.

Appears when nanoe™ X is being

set to ON.

Displays the present time.

Timer program indication

: The indoor unit starts

operation at the programmed time.

: The indoor unit stops

operation at the programmed time.

Indicates the remote controller

addresses are set.

Appears when the function is not

available.

The ON timer or the OFF timer

will operate repeatedly every day.

Indicates the

position.

Indicates the fan speed.

Displays the selected operation

mode. (AUTO /HEAT /

DRY /COOL /FAN )

Energy saving operation is in

process.

Appears when a fan available in the

market is installed and is operating.

“Temperature Automatic Return”

is set.

Appears when the setting screen

is displayed.

8-2-1-2

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 2

20/01/14 10:04:17

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды