Panasonic S-3650PF3E Скачать руководство пользователя страница 143

Страница: 143 / 321

1-11-1-2-24

●

Connecting Tubing Between Indoor and Outdoor Units

Indoor Unit Tubing Connection

Unit : mm

Indoor unit type

S-3650PF3E

S-6071PF3E

ø12.7

Gas tube

ø15.88

Liquid tube

ø6.35

ø9.52

(1) Tightly connect the indoor-side refrigerant tubing extended from the wall with the outdoor-side tubing.

(2) To fasten the flare nuts, apply specified torque.

When removing the flare nuts from the tubing connections, or when tightening them after connecting the tubing,

be sure to use two spanners. When tightening the flare nuts, use a torque wrench.

If the flare nuts are over-tightened, the flare may be damaged, which could result in refrigerant leakage and

cause injury or asphyxiation to room occupants.

●

Outdoor unit

Torque wrench

Spanner

Indoor unit

1) When using with single connection

Liquid tube (ø6.35)

Connect the gas socket tube A (ø12.7 - ø15.88)

to the gas tubing side indoor unit

Connect the liquid socket tube B (ø6.35 - ø9.52)

to the liquid tubing side indoor unit

Gas tube (ø12.7)

• Outdoor PZ3 series (Type 71)

• Outdoor PZ3 series (Type 60)

How to use different-diameter-tube joint (supplied)

Liquid tube (ø6.35)

Gas tube (ø15.88)

Connect the liquid socket tube B (ø6.35 - ø9.52)

to the liquid tubing side indoor unit

Different-diameter-tube joint for the indoor unit tubing connection part is supplied with S-6071PF3E.

The size of parenthesis indicates the connection tube diameter when using the different-diameter-tube joint.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 24

20/01/30 10:25:54

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды