Panasonic S-3650PF3E Скачать руководство пользователя страница 92

Страница: 92 / 321

1-11-1-1-16

<Procedure of CZ-RTC5 >
Stop the system before performing these steps.

Keep pressing the

and

buttons

simultaneously for 4 or more seconds.
The “Maintenance func” screen appears on the LCD
display.

Press the

button to see each menu.

If you wish to see the next screen instantly, press the

button.

Select “8. Detailed settings” on the LCD display and
press the

button.

The “Detailed settings” screen appears on the LCD display.

Select the “Unit no.” by pressing the

button for changes.

Select the “Code no.” by pressing the

button.

Change the “Code no.” to “

” by pressing the

button (or keeping it pressed).

=91

=90

=92

=93

Electrical component box

Select the “Set data” by pressing the

button.

Select one of the Setting Data “YYYY” by pressing the

button.

Then press the

button.

Flap position

* Setting data “

”

Setting data

Flap position during operation

Without separate setting

Swing

Move to position

and stay

Move to position

and stay

Move to position

and stay

Move to position

and stay

Move to position

and stay

NOTE

The flap swings during the operation under “Setting
the Flap Separately”.
At this time, the unselected flaps are moved to the
position

Press the

button.

The “Exit detailed settings and restart?” (Detailed setting-
end) screen appears on the LCD display.

Select “YES” and press the

button.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 16

20/01/30 10:25:12

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды