Panasonic S-3650PF3E Скачать руководство пользователя страница 97 | Manualshive

Страница: 97 / 321

background image

1

1-11-1-1-21

(4) Wiring the Panel for Cassette

1) Open the cover of the electrical component box for

the indoor unit control PCB.

2) Connect the 22P connector (white) and 6P connector

(white) from the panel for cassette to the connector on
the indoor unit control PCB in the unit electrical
component box.
In this case, expose the cutout section of the tube for
the wiring protection to the outside from the electrical
component box and fix it with the clamper attached to
the electrical component box.

Insert connector lock facing PCB edge until it is
locked in place. (If not connected completely, the
Auto Flap will not operate and “P09” is displayed
on the remote controller. When the connector
plugged in the wrong direction, parts on the PCB
may be damaged.)

Check that the wiring connector is not caught
between the electrical component box and the
cover.

Check that the wiring connector is not caught
between the unit and the panel for cassette.

(5) How to Attach the Corner & Air Intake Grille

A. Attaching the corner cover

1) Check that the safety strap from the corner cover is

fastened to the panel for cassette pin, as shown in the
figure below.

2) Use the supplied screws to attach the corner cover to the

panel for cassette.

Pin

Place the corner cover

so that the 5 tabs fit into

the holes in the panel

for cassette. Then

fasten it in place with

the supplied screws.

Supplied screw

B. Attaching the air intake grille

To install the air intake grille, follow the steps for
“Removing the grille” in the reverse order. By rotating the
air intake grille, it is possible to attach the grille onto the
panel for cassette from any of 4 directions. Coordinate the
directions of the air intake grilles when installing multiple
units, and change the directions according to customer’s
requests.

When attaching the air intake grille, be careful that the
flap lead wire does not become caught.

Be sure to attach the safety strap that prevents the air
intake grille from dropping off to the panel for cassette
unit as shown in the figure below.

With this panel for cassette, the directions of the air
intake grille lattices when installing multiple units, and the
position of the label showing the company name on the
corner panel, can be changed according to customer’s
requests, as shown in the figure below. However, the
wireless signal receiver can only be installed at the
refrigerant-tubing corner of the ceiling unit.

Hole of panel for cassette hook

Refrigerant tube side

Optional wireless receiver kit

* This position is only possible for

installation.

Corner cover installation position

marked with the Panasonic Logo at

shipment.

* Installation possible at every corner

Electrical component box

ECONAVI sensor

*This installation position cannot be moved to another location.

Can be installed

rotated 90°

Locations of air intake grille hinges at

shipment
* The grille can be installed with these

hinges facing in any of 4 directions.

Drain pipe side

Hook that prevents the grille from dropping

22P (white)

6P (white)

(For ECONAVI )

Wiring diagram

(Direction that the unit

faces has been changed to

facilitate explanation.)

Connector

Lock

Lid of electrical component box

Cutout section of the tube

for wiring protection

22P (white)

Screws (×2)

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 21

20/01/30 10:25:15

«
...
95
96
97
98
99
...
»

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Бренд: Samsung Страницы: 12

Бренд: Samsung Страницы: 24

Бренд: Samsung Страницы: 295

AW07A(G)2NBA/DE/EA

Бренд: Samsung Страницы: 16

Бренд: ARCTIC WIND Страницы: 17

Бренд: Dimplex Страницы: 11

Бренд: Daikin Страницы: 264

Бренд: Levoit Страницы: 12

ODEUR DE CHINE II

Бренд: Serene House Страницы: 6

Бренд: Aktobis Страницы: 12

Aqu@Scop Advance R410A

Бренд: Airwell Страницы: 134

Бренд: Technibel Страницы: 34

Бренд: Hisense Страницы: 42

Бренд: Goodman Страницы: 20

Бренд: ActivePure Страницы: 2

Suburban Dynaline 3 DYNA07AC

Бренд: ACS Страницы: 38

Бренд: OION Technologies Страницы: 8

Бренд: Acson Страницы: 203

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды