Panasonic S-3650PF3E Скачать руководство пользователя страница 125

Страница: 125 / 321

1-11-1-2-6

Fix the Indoor Unit

Horizontal Installation

Depending on the ceiling type:

a) Insert suspension bolts

b) Use existing ceiling supports or construct a suitable

support.

Hole-in-anchor

Hole-in-plug

Concrete

Insert

Suspension bolt (M10 or 3/8")

(field supply)

Ceiling tiles

Ceiling support

(3) Thread the 3 hexagonal nuts and 2

washers

(field supply) onto each of the 4 suspension bolts. Use

1 nut and 1 washer for the upper part, and 2 nuts and

1 washer for the lower part, so that the unit will not fall

off the suspension lugs.

WARNING

It is important that you use extreme care in supporting

the indoor unit inside the ceiling. Ensure that the

ceiling is strong enough to support the weight of the

unit. Before hanging the unit, test the strength of each

attached suspension bolt.

(1) When placing the unit inside the ceiling, determine the

pitch of the suspension bolts referring to the

dimensional data as shown in the tables and diagrams

under the section 3-1. on page 1-11-1-2-2.

Tubing must be laid and connected inside the ceiling

when suspending the unit. If the ceiling is already

constructed, lay the tubing into position for connection

to the unit before placing the unit inside the ceiling.

(2) Screw in the suspension bolts allowing them to protrude

from the ceiling. (Cut the ceiling material, if necessary.)

Nuts and washers

(use for upper and lower)

Suspension lug

Double nuts

Suspension bolt

Notch

Suspension bolt

Double nuts

Hexagonal nut

This shows an example of installation.

Air outlet duct

Bolt anchor

Suspension bolt

Ceiling material

Air outlet grille

Indoor unit

Vertical Installation

To prevent overturning, fasten the unit to the wall securely.
Check to make sure the wall can endure 5 times of weight

of the unit. Ensure to fix the unit.
In order to suppress vibrations, provide he spacer between

tthe unit and the wall.
Fasten the hanging brackets and bolts using by the hexagon

nuts and washers.
Check to make sure the unit is installed in a horizontal

position by using a level.

Water leakage may occur if the unit is not installed

horizontally.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 6

20/01/30 10:25:46

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды