manualshive.com logo in svg

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Panasonic S-3650PF3E - Мощный и надежный продукт с выдающимися характеристиками. Теперь вы можете с легкостью узнать больше о его технических данных и обслуживании, скачав бесплатный руководство по эксплуатации с manualshive.com. Не упустите шанс загрузить его и улучшить свой пользовательский опыт.

Поделиться
Скачать
background image

1

1-11-1-1-3

●

 Placing the Unit Inside the Ceiling

This unit is equipped with the drain pump. Check a tape 
measure or carpenter’s level.
Before installing the panel for cassette, complete the 
work of drain pipe and refrigerant tube installation.

(1) When placing the unit inside the ceiling, determine the 

pitch of the suspension bolts using the supplied full-scale 
installation diagram.

 

Tubing and wiring must be laid inside the ceiling when 
suspending the unit. If the ceiling is already constructed, 
lay the tubing and wiring into position for connection to 
the unit before placing the unit inside the ceiling.

(2) The length of suspension bolts must be appropriate for a 

distance between the bottom of the bolt and the bottom 
of the unit of more than 18 mm.

(3) Thread the 3 hexagonal nuts and 2 washers onto each 

of the 4 suspension bolts. Use 1 nut and 1 washer for the 
upper side, and 2 nuts and 1 washer for the lower side, 
so that the unit will not fall off the suspension lugs.

Nuts and washers 

(use for upper and lower)

Double nut

12 ~ 17 (mm)

Notch

Suspension lug

Suspension bolt

(4) Adjust so that the distance between the unit and the 

ceiling bottom is 12 to 17 mm. Tighten the nuts on the 
upper side and lower side of the suspension lug.

(5) Remove the protective polyethylene used to protect the 

fan parts during transport.

(6) Check with a tape measure or carpenter’s level.

Full-scale installation diagram 

(printed on top of container box)

Indoor unit

Indoor unit

Paper model 

for installation

Paper model 

for installation

Screw for 

attaching paper 

(4 points)

Open the ceiling

board as large as this 

paper outline

Ceiling

board

Ceiling

board

Ov

er 18 mm

12 ~ 17 mm

281258_EU.indb   9

2016-9-1   13:03:41

3. HOW TO INSTALL THE INDOOR UNIT

● 

Preparation for Suspending

This unit uses a drain pump. Use a carpenter’s level to check
that the unit is level.

● 

Suspending the Indoor Unit

(1) Fix the suspension bolts securely in the ceiling using

the method shown in the diagrams, by attaching them
to the ceiling support structure, or by any other method
that ensures that the unit will be securely and safely
suspended.

Note:  For DC Fan Tap Change Procedure for 4-Way 

Cassette, see page 1-1

1

-1-

1

-1

4

.

Hole-in-anchor

Hole-in-plug

Concrete

Insert

Suspension bolt 
(M10 or 3/8")
(field supply)

Drain outlet (other side)

(VP25)

Suspension lug

* Over 20 mm

* Over 20 mm

340 mm

840 mm

950 mm

272 mm

50 mm

Refrigerant tubing joint (liquid side)

Refrigerant tubing joint (gas side)

184 mm

134 mm

33.5 mm

177 mm

127 mm

Indoor Unit

View from top 

A:

 700 mm

A: 780 mm

B: 860 ~ 910 mm

 A: (suspension bolt pitch)

 B: (ceiling opening dimension)

B:

 860 ~ 910 mm

(2) Follow the diagram to make the holes in the ceiling.

(3) Determine the pitch of the suspension bolts using the supplied full-scale installation diagram (printed on container box). 

The diagram show the relationship between the positions of the suspension fitting, unit, and panel. 
Use the nut (field supply) and washer (supplied) for upper and lower position of the suspension lug.

* The overlapping portion between the ceiling and panel for cassette should be kept over 20 mm.

281258_EU.indb   8

2016-9-1   13:03:40

S-3650PU3E: 256 mm

 

S-6071PU3E: 256 mm

 

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb   3

20/01/30   10:25:04

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

York 36 Technical Manual preview
36
Бренд: York Страницы: 44
Bard R-410A Manual preview
R-410A
Бренд: Bard Страницы: 8
York R-410A User Manual preview
R-410A
Бренд: York Страницы: 24
York R-410A Technical Manual preview
R-410A
Бренд: York Страницы: 56
York R-410A Technical & Service Manual preview
R-410A
Бренд: York Страницы: 385
Bard MULTI-TEC W18AAPA Installation And Service Instructions Manual preview
MULTI-TEC W18AAPA
Бренд: Bard Страницы: 51
York TIWM006B21S Installation And Maintenance Manual preview
TIWM006B21S
Бренд: York Страницы: 52
York SCOH-070K Installation Instructions Manual preview
SCOH-070K
Бренд: York Страницы: 40
York Predator XP Series Technical Manual preview
Predator XP Series
Бренд: York Страницы: 54
inventum AC125W Instruction Manual preview
AC125W
Бренд: inventum Страницы: 100
Gree DUCT09HP230V1BD Service Manual preview
DUCT09HP230V1BD
Бренд: Gree Страницы: 51
Daikin FDQ125C7VEB Installation Manual preview
FDQ125C7VEB
Бренд: Daikin Страницы: 16
GreenTec CAS 500 Manual preview
CAS 500
Бренд: GreenTec Страницы: 36
Napoleon NH19-24F User Manual preview
NH19-24F
Бренд: Napoleon Страницы: 27
BestAir AirJet 2000 Manual preview
AirJet 2000
Бренд: BestAir Страницы: 14
turbionaire 5949096154325 Instruction Manual preview
5949096154325
Бренд: turbionaire Страницы: 50
Vertiv Liebert CRV Plus User Manual preview
Liebert CRV Plus
Бренд: Vertiv Страницы: 98
McLean Cooling Technology LOBOY 16 Instruction Manual preview
LOBOY 16
Бренд: McLean Cooling Technology Страницы: 12

Бренды по названию

Популярные бренды

Загрузить еще бренды