Panasonic S-3650PF3E Скачать руководство пользователя страница 152 | Manualshive

Страница: 152 / 321

background image

1

1-11-2-1-1

1. U-36PZ3E5, U-50PZ3E5, U-60PZ3E5, U-71PZ3E5

Outdoor Unit

WARNING

The appliance shall be stored, installed and operated in a well ventilated room with indoor

ﬂ

oor area larger than

A

min

(m²) [refer to Check of Density Limit] and without any continuously operating ignition source. Keep away from open

ﬂ

ames, any operating gas appliances or any operating electric heater. Else, it may explode and cause injury or death.

The mixing of different refrigerants within a system is prohibited. Models that use refrigerant R32 and R410A have a

different charging port thread diameter to prevent erroneous charging with refrigerant R22 and for safety.

Therefore, check beforehand. [The charging port thread diameter for R32 and R410A is 12.7 mm (1/2 inch).]
Ensure that foreign matter (oil, water, etc.) does not enter the piping.

Also, when storing the piping, securely seal the opening by pinching, taping, etc. (Handling of R32 is similar to R410A.)

Operation, maintenance, repairing and refrigerant recovery should be carried out by trained and certi

ﬁ

ed personnel in

the use of

ﬂ

ammable refrigerants and as recommended by the manufacturer. Any personnel conducting an operation,

servicing or maintenance on a system or associated parts of the equipment should be trained and certi

ﬁ

ed.

Any part of refrigerating circuit (evaporators, air coolers, AHU, condensers or liquid receivers) or piping should not be

located in the proximity of heat sources, open

ﬂ

ames, operating gas appliance or an operating electric heater.

The user/owner or their authorized representative shall regularly check the alarms, mechanical ventilation and detectors,

at least once a year, where as required by national regulations, to ensure their correct functioning.

A logbook shall be maintained. The results of these checks shall be recorded in the logbook.

In case of ventilations in occupied spaces shall be checked to con

ﬁ

rm no obstruction.

Before a new refrigerating system is put into service, the person responsible for placing the system in operation should

ensure that trained and certi

ﬁ

ed operating personnel are instructed on the basis of the instruction manual about the

construction, supervision, operation and maintenance of the refrigerating system, as well as the safety measures to be

observed, and the properties and handling of the refrigerant used.

The general requirement of trained and certiﬁ

ed personnel are indicated as below:

a)

Knowledge of legislation, regulations and standards relating to ﬂ

ammable refrigerants; and,

b)

Detailed knowledge of and skills in handling

ﬂ

ammable refrigerants, personal protective equipment, refrigerant

leakage prevention, handling of cylinders, charging, leak detection, recovery and disposal; and,

c)

Able to understand and to apply in practice the requirements in the national legislation, regulations and Standards; and,

d)

Continuously undergo regular and further training to maintain this expertise.

Air-conditioner piping in the occupied space shall be installed in such a way to protect against accidental damage in

operation and service.

Precautions shall be taken to avoid excessive vibration or pulsation to refrigerating piping.

Ensure protection devices, refrigerating piping and

ﬁ

ttings are well protected against adverse environmental effects

(such as the danger of water collecting and freezing in relief pipes or the accumulation of dirt and debris).

Expansion and contraction of long runs piping in refrigerating systems shall be designed and installed securely (mounted

and guarded) to minimize the likelihood hydraulic shock damaging the system.

Protect the refrigerating system from accidental rupture due to moving furniture or reconstruction activities.

To ensure no leaking,

ﬁ

eld-made refrigerant joints indoors shall be tightness tested. The test method shall have a

sensitivity of 5 grams per year of refrigerant or better under a pressure of at least 0,25 times the maximum allowable

pressure (>1.04MPa, max 4.15MPa). No leak shall be detected.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 1

20/01/30 10:25:57

«
...
150
151
152
153
154
...
»

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Бренд: Unitary products group Страницы: 68

Бренд: Linea 2000 Страницы: 48

Бренд: Panasonic Страницы: 64

Бренд: Daikin Страницы: 38

Бренд: Hisense Страницы: 43

Бренд: Kroll Страницы: 28

Бренд: Turbo Air Страницы: 21

Бренд: NewAir Страницы: 15

Бренд: Trotec Страницы: 16

Бренд: Airmax Страницы: 102

Бренд: Daikin Страницы: 57

Бренд: Goodman Страницы: 48

Бренд: HEIL Страницы: 10

Бренд: Daikin Страницы: 10

PURE LIGHT UV HTWS026PLUV

Бренд: HTW Страницы: 88

Бренд: ActivePure Страницы: 2

Бренд: Gree Страницы: 44

Бренд: Zibro Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды