Panasonic S-3650PF3E Скачать руководство пользователя страница 232

Страница: 232 / 321

5-2-1-3

E01 Remote Controller Reception Error

(When indoor unit(s) are connected)

Error Detection Method

Error Diagnosis

It is judged an error if no self-addressed communication is sent to the remote controller in a 3-minute period.

When a remote controller is set to sub remote controller.

When there are nine or more indoor units in a remote control group’s wiring.

The nonvolatile memory (EEPROM) is not installed or faulty when turning on the power.

Remote controller check mode

Malfunctions of the remote controller itself (reception circuit error)

•

•
•

When the CHK (check pin) and/or TEST (test pin) on the indoor unit control PC board are short circuited.

•

Indoor unit control PC board error

•

2-2
3-1

Is that indoor unit under group control?

Is auto address setting complete?

1-1

Is there an auto address setting error (Is the outdoor unit showing

an alarm)?

1-2

Conduct checks prior to auto address setting.

1-3

2-1

The nonvolatile memory (EEPROM) on the indoor unit’s control PC board is either not

installed, improperly installed or the nonvolatile memory is faulty. Correct this or after

replacing the nonvolatile memory, write model data to it in the remote control detailed

settings mode.

3-6

Is there a short, miswiring, disconnection, wrong contact or

grounding in the remote control’s wiring?

3-7

Is the LED blinking on the indoor unit’s control PC board?

3-5

Are there any indoor units with their power off in the remote

control group’s wiring?

2-2

Are the CHK pin and TEST pin on the indoor unit control board

short-circuited?

3-1

3-3
3-5

Is the wireless remote controller connected to on the indoor unit’s

control PC board?

3-2

3-4

3-5

Disconnect the connector mentioned above on the PC board of the

indoor unit control PC board, and see whether the E01 goes off after

several minutes. (When doing so, if two remote controllers are

being used and the wireless remote controller is the main remote

controller, set the other remote controller as the main.)

3-3

3-7

3-6

1-2
1-3
1-3
2-1

Power on
2-3

Remove the short
3-2

Yes

Correct the wiring
2-4

Are nine or more indoor units connected in one remote control

group’s wiring?

2-3

Was the remote control group’s wiring changed after auto address

setting was complete? Alternatively, were group settings changed

in the remote control detailed settings mode?

2-4

2-5
3-1

Yes

Replace wireless remote control parts including wiring.

3-4

No main unit in the remote control group’s wiring? Re-execute auto address setting.

2-5

Installation

or setting

Group

Control

Wiring

1 Auto

Address

Yes

Replace the indoor

unit’s control board.

Correct the wiring

Yes

Regarding the remote controller check, refer to the Reference Materials.

•

For information on the procedures for replacing the nonvolatile memory (EEPROM) of the indoor unit and/or replacing the

indoor unit’s control board, refer to the manual that is packaged with the indoor unit service board.

•

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 3

2020/01/29 21:17:41

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды