Panasonic S-3650PF3E Скачать руководство пользователя страница 182

Страница: 182 / 321

2-3-1-1

Type U3, Type F3

2-3. Indoor Units

2-3-1-1. Caution

The indoor and outdoor unit control PCB utilizes a semiconductor memory element (EEPROM).

The settings required for operation were made at the time of shipment.

Only the correct combinations of indoor and outdoor units can be used.

This test run section describes primarily the procedure when using the wired remote controller.

2-3-1-2. Test Run Procedure

Recheck the items to check before the test run.

Indicate (mark) the combination number

Set the remote controller to “Test run”.

Return the remote controller to normal control.

Can

operation be

started?

(See section 2-3-1-3)

YES

Check the combination

(wiring) of indoor and outdoor units.

Is system “3-LINE CONNECTION”?

(See section 2-3-1-6-2, 2-3-1-6-3, 2-3-1-6-4)

(See section 2-3-1-6-1)

(See section 2-3-1-6-5)

(See section 2-3-1-4)

Address Setting

3-LINE CONNECTION

See section “2-3-1-5. Contents of Remote

Controller Switch Alarm Display” to check

the system.

In addition, see section 2-3-1-6-1 to 2-3-1-6-6

and correct any items that need to be

corrected.

NOTE

Check the indoor-side drainage.

2-3-1-3. Items to Check Before the Test Run

(1) Turn the remote power switch ON at least 5 hours in advance in order to energize.
(2) Fully open the closed valves on the liquid tubing and gas tubing sides.
(3) Separate the power supply in accordance with the types of system.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 1

2020/01/29 19:52:15

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды