Panasonic S-3650PF3E Скачать руководство пользователя страница 118

Страница: 118 / 321

1-11-1-1-42

● Details of parts

● Procedure for attaching the parts

Parts installed on the indoor unit

Part

name

Shape

No. of

parts

Part

name

Shape

No. of

parts

Part

name

Shape

No. of

parts

Side panel insulator

Perforations

Slit

Square

hole

Perforations

Side panel insulator

Ceiling insulator

Hanger insulator

Installation instructions

Ceiling insulator

Side panel insulator

* Indoor unit has two kinds of heights.(Large unit=319mm, Small unit=256mm)

When attaching the side panel insulator to the small unit, attach it after cutting along its perforations of the

parts<1> to <5>

1. Align the slits of the side panel insulators <1> to <4> with the hanger, and attach the parts to the side panels of

the indoor unit. (Fig. 1)

2. Now attach the side panel insulator <5> to the side panel of the indoor unit. (Fig. 1)

3. Align the side panel insulator <6> with the piping cover, and attach the part. (Fig. 1)

4. Attach the ceiling insulators <7> to <9> in such a way that no gaps are left. (Fig. 2)

Do the following procedures after installing the indoor unit.

5. Attach the hanger insulators <10> to the hangers in the directions shown in the figure. (Fig. 3)

Keep hanger insulator<10> until installing the indoor unit.

When attaching the insulators,

ensure that they overlap.

(Side insulators <1> to <5>)

(In 4 places)

Fig.

-10

Fig.

-11

Parts installed on the indoor unit (continued)

<1>

<2>

<3>

<4>

<6>

<7>

<8>

<5>

<9>

<10>

<2>

<1>

<3>

<6>

<5>

<7>

<8>

<9>

<10>

Fig. 1

-9

<4>

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 42

20/01/30 10:25:32

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды