manualshive.com logo in svg

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Panasonic S-3650PF3E - Мощный и надежный продукт с выдающимися характеристиками. Теперь вы можете с легкостью узнать больше о его технических данных и обслуживании, скачав бесплатный руководство по эксплуатации с manualshive.com. Не упустите шанс загрузить его и улучшить свой пользовательский опыт.

Поделиться
Скачать
background image

1

1-11-1-1-31

 Troubleshooting

If your air conditioner does not work properly, first check the following points before requesting service. If it still does not work 
properly, contact your dealer or a service center.

 

Indoor unit

Symptom

Cause

Noise

Sound like streaming water during 
operation or after operation

 

Sound of refrigerant liquid flowing inside unit

 

Sound of drainage water through drain pipe

Cracking noise during operation or 
when operation stops.

Cracking sound due to temperature changes of parts

Odor

Discharged air is smelled during 
operation.

Indoor odor components, cigarette odor and cosmetic odor accumurated 
in the air conditioner and its air is discharged. 
Unit inside is dusty. Consult your dealer.

Dewdrop

Dewdrop gets accumurated near air 
discharge during operation

Indoor moisture is cooled by cool wind and accumulated by dewdrop.

Fog

Fog occurs during operation in 
cooling mode. 
(Places where large amounts of oil 
mist exist at restaurants.)

 

Cleaning is necessary because unit inside (heat exchanger) is dirty. 
Consult your dealer as technical engineering is required.

 

During defrost operation

Fan is rotating for a while even though operation 
stops.

 

Fan rotating makes operation smoothly.

 

Fan may sometimes rotates because of drying heat exchanger due to 
settings.

 

Fan may sometimes rotates in internal cleaning operation mode for 

a while. 

Wind-direction changes while operating.
Wind-direction setting cannot be made.
Wind-direction cannot be changed.

 

When air discharge temperature is low or during defrost operation, 
horizontal wind flow is made automatically.

 

Flap position is occasionally set up individually.

When wind-direction is changed, flap operates 
several times and stops at designated position.

When wind-direction is changed, flap operates after searching for 
standard position.

Dust

Dust accumulation inside indoor unit is discharged. 

Poor cooling or heating performance

The indoor unit is initially designed to control the indoor temperature 
detected by the built-in room sensor inside the indoor unit.
Due to indoor unit installation position, however, the built-in sensor may 
occasionally sense temperature improperly; for example, temperature 
difference between the ceiling and floor, lighting apparatus, electric fan, 
windows or waist-high partition walls, etc.
In this case, the unit does not operate properly at the desired 
temperature.
You may change the use of the temperature sensor inside the indoor unit 
to that of the remote controller.
Then the desired room temperature can be controlled properly.
For details, consult your dealer.

 

CAUTION

  Certain metal edges and the condenser fins are sharp 

and may cause injury if handled improperly; special care 

should be taken when you clean these parts.

  Periodically check the outdoor unit to see if the air outlet 

or air intake is clogged with dirt or soot.

  The internal coil and other components must also be 

cleaned periodically. Consult your dealer or service 

center.

Care: After a prolonged idle period

Check the indoor and outdoor unit air intakes and outlets for 

blockage; if there is a blockage, remove it.

Care: Before a prolonged idle period

  Operate the fan for half a day to dry out the inside.
  Disconnect the power supply and also turn off the circuit 

breaker. 

  Clean the air filter and replace it in its original position.
  Outdoor unit internal components must be checked and 

cleaned periodically. Contact your local dealer for this 

service.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb   31

20/01/30   10:25:19

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Zanotti GS Series Use And Maintenance Instructions preview
GS Series
Бренд: Zanotti Страницы: 84
W.Tech RAA Series Installation And Maintenance Manual preview
RAA Series
Бренд: W.Tech Страницы: 16
Technibel KPW 2 Operating Instructions Manual preview
KPW 2
Бренд: Technibel Страницы: 8
EnviroPureFX EPFX HEPA375VSC Owner'S Manual preview
EPFX HEPA375VSC
Бренд: EnviroPureFX Страницы: 4
Iwata V-MAX Instruction Manual preview
V-MAX
Бренд: Iwata Страницы: 6
Parker Hyperchill PCW040 User Manual preview
Hyperchill PCW040
Бренд: Parker Страницы: 72
Lennox HCF RTL G 17 User'S Information Manual preview
HCF RTL G 17
Бренд: Lennox Страницы: 5
Coway AP-1009CH User Manual preview
AP-1009CH
Бренд: Coway Страницы: 124
Daikin MC40VBFVM3 Operation Manual preview
MC40VBFVM3
Бренд: Daikin Страницы: 48
OBH Nordica 6154 Instruction Manual preview
6154
Бренд: OBH Nordica Страницы: 40
easymaxx TS-20964R Instruction Manual preview
TS-20964R
Бренд: easymaxx Страницы: 42
Danby DTAC100B1WDB-RF Owner'S Manual preview
DTAC100B1WDB-RF
Бренд: Danby Страницы: 25
Airgle PurePal AG900 User Manual preview
PurePal AG900
Бренд: Airgle Страницы: 5
UFESA PF5500 fresh air Instruction Manual preview
PF5500 fresh air
Бренд: UFESA Страницы: 52
ECG MK 124 Instruction Manual preview
MK 124
Бренд: ECG Страницы: 76
Frico Sunnan SUN12 Original Instructions Manual preview
Sunnan SUN12
Бренд: Frico Страницы: 9
SANITY SYSTEM SANY-MED-80 Instruction Manual preview
SANY-MED-80
Бренд: SANITY SYSTEM Страницы: 36
Kaysun KAM2-52 DR7 Owner'S Manual preview
KAM2-52 DR7
Бренд: Kaysun Страницы: 16

Бренды по названию

Популярные бренды

Загрузить еще бренды