Panasonic S-3650PF3E Скачать руководство пользователя страница 245

Страница: 245 / 321

5-2-1-16

Remove the short
2-1

Are the CHK pin, TEST pin and DISP pin on the indoor unit control

PC board short-circuited?

Is the indoor unit powered off?

1-1

1-2

3-4

Is the remote control group’s wiring opened?

2-1

Is the wiring of the remote control group wired according to the

wiring diagram?

2-3

Run the auto address setting again.

2-4

Run the auto address setting again after correcting the wiring of the remote control group.

2-5

Power on

1-2

Correct the wiring
2-2

2-4
2-5

Yes

2-3
3-1

Yes

Check the group settings (Item Code 14) from the remote control’s

detailed settings mode. Is the main remote controller (1) set to more

than one remote controller or to separate (0)?

2-2

Substitute

Sub

Remote

Controller

1 Indoor Unit

E18 Faulty Communication in Group Control Wiring

Error Detection Method

Error Diagnosis

When the main remote controller cannot communicate with a sub remote controller in the remote control group.

It is judged an error if a sub remote controller in a remote control group fails to communicate with the main remote controller

for a period of three minutes.

An indoor unit within the control group does not have its power on.

The CHK pin and TEXT pin on the indoor unit in the control group are shorted.

Remote control group wiring is opened.

More than one indoor unit in the control group is set to Main.

An indoor unit in the control group is set to Separate.

•

•
•

•

The DISP pin of an indoor unit sub remote controller in the control group is shorted.

•

Replace wireless remote control parts including wiring.
Replace the indoor unit control PC board.

3-3

Is the wireless remote controller connected to on the indoor unit’s

control PC board?

3-1

Disconnect the connector mentioned above on the control PC board

of the indoor unit control PC board, and see whether the E18 goes off

after several minutes. (When doing so, if two remote controllers are

being used and the wireless remote controller is the main remote

controller, set the other remote controller as the main.)

3-2

Yes 3-2

3-4

3-3

3-4

Yes

Indoor

unit

control

PCB

For information on the remote control’s detailed settings, refer to the Reference Materials.

•

For information on the procedures for replacing the Indoor unit control PCB, refer to the manual that is packaged with the

indoor unit service board.

•

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 16

2020/01/29 21:17:48

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды