Panasonic S-3650PF3E Скачать руководство пользователя страница 299

Страница: 299 / 321

•

Pinch the handle and open while pressing it towards the mark.

▼

Battery cover

Handle

RC reset button

4. Put the battery cover back on.

■ Notes on batteries

• The battery life is approximately 1 year.

• Reception may become poor or display on the remote controller fades when batteries are low.

• If the remote controller will not be used for a long period of time, remove the batteries. (In order to avoid a battery leak.)

• Emergency operations can be performed on the unit when the batteries run out. (See page 8-2-1-9)

■ Replacing batteries

• Replace both batteries at the same time with 2 LR03 size batteries.

• Do not use rechargeable batteries (NiCd, NiMH, etc.) because their size, shape, and some performance are different.

• Dispose of the old batteries at the designated sites in your community.

• The unit is restored with the factory setting when batteries are removed.

• After changing the batteries, reset the current time. (See Section “8-2-1-3. Setting the Current Time”)

2, 3

Remove the battery cover.

Insert two LR03 size batteries.

Put the batteries in with the polarity [+/–] as shown in the figure

Gently insert one end of an unfolded paper clip (or a similar object that can it) into the RC reset hole and press the

RC reset button inside the hole.

• Take the batteries out and insert again if the time display is not “ ” or “ ”.

8-2-1-2. Installing Batteries

8-2-1-3

. Setting the Current Time

1. Press for 2 seconds or longer.

• The time display flashes. (The colon lights up.)

2. Press / to set the hour, then press .

3. Press / to set the minutes, then press .

Note

• If the buttons are not pressed for a certain duration while setting the time,

the displayed time is set.

• Adjust the time periodically.

If a heat pump (2WAY) type is being used, it will beep twice a

d the operating lamp will light up on the display; if the timer

and standby lamps blink alternately, a conflict between the he

ing and cooling exists, so the unit cannot operate in the

desired mode. (On models that do not have an Auto function,

ven if Auto is selected, it works in the same way.)

When the local operation is disabled by centralized control or

similar cause, and if the Start/Stop ,

ode

Temperature setting button is pressed, the unit w

ll beep five times and the change will not be made.

8-2-1-3

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 3

20/01/14 10:04:18

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды