Panasonic S-3650PF3E Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 321

background image

1

1-10-2-1-1

1. U-36PZ3E5, U-50PZ3E5, U-60PZ3E5, U-71PZ3E5

ELECTRICAL WIRING

Warning

This air conditioner must be installed in accordance with national wiring regulations.
Cables connected to outdoor unit must be approved polychloroprene sheathed type 60245 IEC 57 or

H05RN-F/H07RN-F or heavier.
The units must be connected to the supply cables for

ﬁ

xed wiring by quali

ﬁ

ed technician.

Circuit breaker must be incorporated in the ﬁxed wiring in accordance with the national wiring regulations.

When the supply cable is damaged, it must be replaced by quali

ﬁ

ed technician.

Be sure to install a current leakage breaker, main switch and fuse to the main power supply, otherwise electric shocks may result.
Be sure to connect the unit to secure earth connection.

If the earthing work is not carried out properly, electric shocks may result.

Wiring shall be connected securely by using speciﬁed cables and ﬁx them securely so that external force of the cables may not transfer to

the terminal connection section.

Imperf

ect connection and ﬁ

xing leads to

ﬁ

re, etc.

Remove the control board cover and terminal board cover from the unit by loosening the screw.

Ensure to connect the electrical cable connections and clamp the wires securely to the terminal connections using cord clamps so that no undue force is placed on

the wires (power source cable, connection cable between indoor and outdoor unit, earth lead wire).

Connect the power supply cord and connecting cable between indoor unit and outdoor unit according to the diagram below.

Terminals on the indoor unit

L/1 N/2 3

Colour of wires (Connecting cable)

Terminals on the outdoor unit

L N 1 2 3

(Power supply cord)

Terminals on the isolating device

(Disconnecting means)

(L) (N)

For wire stripping and connection requirement, refer diagram below.

Wire stripping

5 mm

or more

(gap between

wires)

Conductor

over inserted

No loose strand

when inserted

Indoor/

outdoor

connecting

terminal

board

WIRE STRIPPING AND CONNECTING REQUIREMENT

Conductor

fully inserted

Conductor not

fully inserted

10 ± 1 mm

ACCEPT

PROHIBITED

PROHIBITED

Do not install a phase advance capacitor for power factor improvement. (It does not improve the power factor and will cause abnormal overheating.)

Do not bind the excess cables together and place them inside this unit.

Make sure that terminal board cover and control board cover mount correctly.

Use the appropriate screwdriver for tightening the terminal screws. Small sized screwdriver damages the head of the screw and cannot tighten it properly.

L N

1 2 3

Holder

Earth wire

longer than

others AC wires

for safety reason

Earth wire

longer than

others AC wires

for safety reason

Power

supply cable

Isolating Devices

Indoor Unit

Connection cable between

outdoor and indoor unit

Terminal

Board

OUTDOOR UNIT/SINGLE-PHASE MODEL

L/1

N/2

3

R1

R2

U1

U2

L

N

1

2

3

Connection cable between

outdoor and indoor unit

Outdoor unit power supply

Switch

Fuse

Earth

Indoor unit Remote controller (option)

Outdoor unit

Earth

(Option)

Integrated control system

Terminal board

Terminal board cover

Control board cover

The circuit breaker must be approved, suitable for the voltage and current ratings of equipment and have a contact separation by 3mm in all poles.

There is risk of damaging the screw if the terminal screw is over tightened. Tighten with the appropriate torque 1.57N

•

m ~ 1.96N

•

m (16kgf

•

cm~20kgf

•

cm).

Outdoor Unit

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 1

20/01/30 10:25:00

«
...
73
74
75
76
77
...
»

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Бренд: easymaxx Страницы: 8

Бренд: Godrej Страницы: 50

Бренд: GE Страницы: 36

GWC09NA-D3NNA3A/I

Бренд: Gree Страницы: 72

Бренд: BOMANN Страницы: 74

Excelair EPA101A

Бренд: Excelsior Страницы: 16

23-11-2228N-004

Бренд: Maytag Страницы: 24

Бренд: Villara Страницы: 16

air&me 3700459000039

Бренд: airnaturel Страницы: 35

GWC07NA-K3NNB1A

Бренд: Gree Страницы: 35

Бренд: clair Страницы: 8

Бренд: Samsung Страницы: 30

Бренд: Samsung Страницы: 77

Бренд: Samsung Страницы: 28

Бренд: Haier Страницы: 8

Бренд: Haier Страницы: 13

Бренд: Haier Страницы: 22

Бренд: Haier Страницы: 23

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды