Panasonic S-3650PF3E Скачать руководство пользователя страница 308

Страница: 308 / 321

You can restore the changed temperature to the originally set temperature automatically after a specified

time elapses.

• Set the time and temperature for each operation mode.

1. Press and at the

same time for 4 seconds or longer.

• “ ” starts blinking and the setting screen is displayed.

2. Press to select the operation mode, then press .

• Every time you press to switch between “Dry / Cool

→ Heat → Auto ”, the buzzer sounds from the

corresponding receiver.

• When not set: 1 short beep

• When already set: 2 short beeps

3. Press / to set the time to return to the set

temperature.

• Setting range: 10 to 240 min (by the 10 min)

4. Press / to set the

temperature, then press .

MAX (°C

)

MIN (°C)

Auto

Heat

Dry / Cool

8-2-1-17. Temperature Automatic Return

• The temperature range that can be set varies depending on the model.

5. Press .

• You can return to Step 2 to continue setting if you press instead of .

2, 4
5

1, 4

1, 3

emperature

ime

(min)

Operation mode

Changing the setting

Perform Step 1 to 5 noted above as you did when setting.

Cancelling the setting

1. Press

and

at the same time for 4 seconds or longer.

2. Press

to select the operation mode, then press

for 4 seconds or longer.

• The receiver emits 1 short beep.

• Press for 10 seconds or longer to cancel settings for all operation modes.

Note

• Press to stop operation in the middle.

8-2-1-12

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 12

20/01/14 10:04:20

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды