Panasonic S-3650PF3E Скачать руководство пользователя страница 114

Страница: 114 / 321

1-11-1-1-38

Air-flow blocker

(

470×65×T10)

Air-flow blocker

Air outlet

Sealer (570×90×T2)

Air-flow

blocker B

Air-flow

blocker A

Sealer

Air-flow

blocker A

Sealer

Wire

Indoor unit

Refrigerant

piping

Electrical

component box

Drain piping

Installation instructions

Part name

<Fig. 1>

1. Accessory parts

2. Mounting procedure

The accessory parts are required for the installation work so they should not be discarded until the work is

completed.

No. of

parts

Part name

No. of

parts

Part name

No. of

parts

(1) Checking where the air-flow blocker is to be attached

(2) Fit the air-flow blocker into place to match the shape of the air outlet,adhere the tape of the both side of air-flow blocker

to the drain pan and adhere the sealer on top to block the passage of air. (Fig. 2) (Fig. 3)

Cut off

Tape

Sealer

Tape

Air-flow blocker A

Air-flow blocker B

<Fig. 2>

<Fig. 3>

<Fig. 4>

Air outlet<3>

Air outlet<1>

Air outlet<2>

Air outlet<4>

Refrigerant

piping

Drain

piping

“nanoe”air outlet

Air outlet blocking patterns

As seen from underneath the indoor unit

3-way air outlet

One outlet can be

blocked.

Air outlet duct

connection flange

(

150):field supply

connection 3-way air

outlet

One outlet can be

blocked and

connected to a duct.

Air outlet duct

connection flange

(

150):field supply

connection 2-way air

outlet

Two outlets can be

blocked and

connected to a duct.

Note: The duct can

be connected

only in one of

the locations

shown.

2-way air outlet

Two outlets can be

blocked.

● When a 2- or 3-way air outlet configuration is used or when the

air outlet duct connection flange (

150):field supply

is connected, block the air outlets as per the air outlet blocking

patterns illustrated below.

Also,

see

the table below, and decide on where the pipings

are

to be positioned.

(To better understand what the illustrations show,

see

the

figure

on the right.)

Note: Take care to prevent cold air leaks and deficient insulation

while performing the air outlet duct connection flange

(

150):field supply work in order to prevent condensation

from forming.

● It should be borne in mind that any air outlet blocking pattern with

the hatching mark will make it impossible for the “nanoe”

nano-technology fine particle function to work.

● Under no circumstances must any air outlet blocking patterns not

shown in the table below be used.

Blocking area

Air outlet duct

connection flange

(

150):field supply

<1>

<3>

<2>

<4>

Air outlet

direction

Refrigerant

piping

“nanoe”

air outlet

Drain

piping

■ Changing the DC fan tap settings

For Air outlet<1>

When Air-flow blocker A is to be attached, cut it in

parallel with the slit. (Fig. 1)

For Air outlet<2>

Air-flow blocker B can be used as is.

For Air outlet<3>or<4>

Air-flow blocker A can be used as is.

While referring to “Selecting the DC fan motor taps”

change the DC fan speed by using the wired remote

controller or by setting the DIP switches on the indoor unit control PCB.

<1>

<2>

<3>

<4>

Ｂ

Drain pan

Adjust the position of packing

and attach it so that "a" can be

10mm and more.

Corner metal

・

Fold the protruding parts of the sealer over the side

panel, and adhere them into place.

・

Ensure that the sealer does not come

into contact

with the corner metal fitting.

・

Cut the sealer diagonally so that no contact is made

with the wire.

(3) Adhere the sealer to the drain pan with an

overlap of 10 mm or

more.

(Condensation may form if it is adhered with no overlap.) (Fig. 4)

■

Air-flow Blocking Kit

CZ-CFU3

Installation Instructions

Fig. 1-11-1-1-5

Fig. 1-11-1-1-6

Fig. 1-11-1-1-7

Air-flow blocker

Double-sided tape

Drain pan

(3) Adhere the sealer to the drain pan with an overlap of 10 mm or more.

(Condensation may form if it is adhered with no overlap.)

(fig. 1-11-1-1-7)

Ensure that the sealer does not come into contact

with the corner metal fitting.

Cut the sealer diagonally so that no contact is made

with the wire.

Fold the protruding parts of the sealer over the side

panel, and adhere them into place.

Sealer

Air-flow blocker

Drain pan

Air outlet

(Sectional view)

Drain pan

(Top view)

Please affix in accordance

with the end of the drain pan.

Drain pan

(Sectional view)

Double-sided tape

Air-flow blocker (470×65×T10)

Air-flow blocker

Air outlet

Sealer (570×90×T2)

Installation instructions

Part name

Fig. 1-11-1-1-4

Accessory parts

Mounting procedure

The accessory parts are required for the installation work so they should not be discarded until the work is

completed.

No. of

parts

Part name

No. of

parts

Part name

No. of

parts

(1) Checking where the air-flow blocker is to be attached

(2) Fit the air-flow blocker into place to match the shape of the air outlet,adhere the tape of the both side of air-flow blocker

to the drain pan and adhere the sealer on top to block the passage of air. (Fig. 1-11-1-1-5) (Fig. 1-11-1-1-6)

Cut off

Double-sided tape

Tape

Sealer

Tape

Double-sided

tape

Air-flow blocker A

Air-flow blocker B

Fig. 1-11-8

Fig. 1-11-9

Fig. 1-11-10

Air outlet<3>

Air outlet<1>

Air outlet<2>

Air outlet<4>

Refrigerant

piping

Drain

piping

“nanoe”air outlet

3. Air outlet blocking patterns

As seen from underneath the indoor unit

3-way air outlet

One outlet can be

blocked.

Air outlet duct

connection flange

(Φ150):field supply

connection 3-way air

outlet

One outlet can be

blocked and

connected to a duct.

Air outlet duct

connection flange

(Φ150):field supply

connection 2-way air

outlet

Two outlets can be

blocked and

connected to a duct.

Note: The duct can

be connected

only in one of

the locations

shown.

2-way air outlet

Two outlets can be

blocked.

●

When a 2- or 3-way air outlet configuration is used or when the

air outlet duct connection flange (

150)

field supply

is connected, block the air outlets as per the air outlet blocking

patterns illustrated below.

Also, refer to the table below, and decide on where the pipings

are to be positioned.

(To better understand what the illustrations show, refer to the

figure on the right.)

Note

Take care to prevent cold air leaks and deficient insulation

while performing the air outlet duct connection flange

(

150)

field supply work in order to prevent condensation

from forming.

●

It should be borne in mind that any air outlet blocking pattern with

the hatching mark will make it impossible for the “nanoe”

nano-technology fine particle function to work.

●

When the air-flow blocker has been provided in any air outlet

blocking pattern with the hatching mark, set the “nanoe” function

to “off” using the remote controller.

●

Under no circumstances must any air outlet blocking patterns not

shown in the table below be used.

Blocking area

Air outlet duct

connection flange

(

150)

field supply

<1>

<3>

<2>

<4>

Air outlet

direction

Refrigerant

piping

“nanoe”

air outlet

Drain

piping

■

Changing the DC fan tap settings

For Air outlet<1>

When Air-flow blocker A is to be attached, cut it in

parallel with the slit. (Fig. 1-11-1-1-4)

For Air outlet<2>

Air-flow blocker B can be used as is.

For Air outlet<3>or<4>

Air-flow blocker A can be used as is.

While referring to “4. Selecting the DC fan motor taps,” change the DC fan speed by using the wired remote

controller or by setting the DIP switches on the indoor unit control PCB.

Ｂ

Drain pan

Adjust the position of packing

and attach it so that "a" can be

10mm and more.

・

Fold the protruding parts of the sealer over the side

panel, and adhere them into place.

・

Ensure that the sealer does not come

into contact

with the corner metal fitting.

・

Cut the sealer diagonally so that no contact is made

with the wire.

(3) Adhere the sealer to the drain pan with an

overlap of 10 mm or

more.

(Condensation may form if it is adhered with no overlap.) (Fig. 1-11-10)

Air-flow

blocker B

Air-flow

blocker A

Sealer

Air-flow

blocker A

Sealer

Wire (*2)

Indoor unit

Refrigerant

piping

Electrical

component box

Drain piping

<1>

<2>

<3>

<4>

Corner metal

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 38

20/01/30 10:25:28

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды