Panasonic S-3650PF3E Скачать руководство пользователя страница 193 | Manualshive

Страница: 193 / 321

background image

2

2

2-3-1-12

2-3-1-6-4. How to Set Refrigerant System Address

(1) Keep pressing the

,

and buttons

simultaneously for 4 or more seconds.
The “Maintenance func” screen appears on the LCD display.

Maintenance func

Sel.

20:30 (THU)

1. Outdoor unit error data

2. Service contact

3. RC setting mode

4. Test run

Page [

] Confirm

Turn on the power in the indoor and outdoor units of the refrigerant system 1.
Switch the power on and wait at least 1 minute and 30 seconds or more. Short-circuit the auto address pin of the
outdoor unit with turned on and release. (LED1 and LED2 of the outdoor unit control PCB blink alternately and
the address setting of the indoor unit is started. When completed, LEDs go off.)
<It takes about 10 min

utes until it ﬁnished.>

Auto address pin: If you once again short-circuit the auto address pin before completion when the auto address
started, the auto address will stop.
Turn on the different refrigerant system’s indoor and outdoor units and wait at least 1 minute and 30 seconds or
more. Then short-circuit the auto address pin of the outdoor unit and release.
Repeat the same procedure and complete the auto address setting of each system.
When the address setting is completed, wait at least 1 minute and 30 seconds or more. Then start the operation.

(2) Press the

or

button to see each menu.

If you wish to see the next screen instantly, press the

or

button.

Select “7. Simple settings” on the LCD display and
press the

button.

Maintenance func

Sel.

20:30 (THU)

Page [

] Confirm

5. Sensor info.

6. Servicing check

7. Simple settings

8. Detailed settings

20:30 (THU)

[ ] START

CZ-RTC5B

(3) The “Simple settings” screen appears on the LCD

display.
Select the “Unit no.” by pressing the

or

button for changes.

Simple settings

Unit no.

Code no.

Set data

ALL

01

0001

20:30 (THU)

Sel.

Next

The indoor unit fan operates only at the selected
indoor unit.

2-3-1-6-5. Checking the Indoor Unit Addresses

Use the remote controller to check the indoor unit address.

CZ-RTC5B (High-spec wired remote controller)

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 12

2020/01/29 19:52:18

«
...
191
192
193
194
195
...
»

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Бренд: Daikin Страницы: 14

Бренд: SPT Страницы: 18

Бренд: AERMEC Страницы: 48

Бренд: TCL Страницы: 44

Бренд: Comfee Страницы: 53

Versati III GRS-CQ10Pd/NhH-M

Бренд: Gree Страницы: 58

Бренд: Altech Страницы: 48

Бренд: Kolin Страницы: 31

Бренд: Daikin Страницы: 64

Бренд: TripleAqua Страницы: 50

Бренд: Daikin Страницы: 20

Бренд: Haier Страницы: 24

Бренд: Haier Страницы: 50

Бренд: Haier Страницы: 8

Бренд: Samsung Страницы: 20

Бренд: Samsung Страницы: 16

Бренд: Samsung Страницы: 20

Бренд: Samsung Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды