Panasonic S-3650PF3E Скачать руководство пользователя страница 77 | Manualshive

Страница: 77 / 321

background image

1

1-11-1-1-1

2. SELECTING THE INSTALLATION SITE

2-1. Indoor Unit

AVOID:

●

areas where leakage of flammable gas may be expected.

●

places where large amounts of oil mist exist.

●

direct sunlight.

●

locations near heat sources which may affect the

performance of the unit.

●

locations where external air may enter the room directly.

This may cause “condensation” on the air discharge ports,

causing them to spray or drip water.

●

locations where the remote controller will be splashed with

water or affected by dampness or humidity.

●

installing the remote controller behind curtains or furniture.

●

locations where high-frequency emissions are generated.

DO:

●

select an appropriate position from which every corner of the

room can be uniformly cooled.

●

select a location where the ceiling is strong enough to

support the weight of the unit.

●

select a location where tubing and drain pipe have the

shortest run to the outdoor unit.

●

allow room for operation and maintenance as well as

unrestricted air flow around the unit.

●

the limitation of the tubing length between the indoor and

the outdoor units should be referred to the Installation

Instructions of the outdoor unit.

●

allow room for mounting the remote controller about 1 m off

the floor, in an area that is not in direct sunlight or in the flow

of cool air from the indoor unit.

4-Way Cassette Type

W

all

indoor unit

indoor unit

min. 1 m

min.

1 m

Ov

er 2.

2

m

min. 3 m

Obstacles

Ceiling

1 m

1 m

1 m

1 m

281258_EU.indb 7

2016-9-1 13:03:39

1-11. Installation Instructions

■

Indoor Unit

1. 4-Way Cassette Type (U3)
S-3650PU3E, S-6071PU3E

●

SELECTING THE INSTALLATION SITE

Outdoor unit

Model

(A) Power supply cable

Min. wire size

(mm

2

)

Time delay fuse or

circuit capacity (A)

U-36PZ3E5

220-230-240V ~

2.5

15

U-50PZ3E5

220-230-240V ~

2.5

15

U-60PZ3E5

220-230-240V ~

2.5

20

U-71PZ3E5

220-230-240V ~

2.5

20

Refer to the installation instruction manual provided with the indoor unit.

The product meets the technical requirements of EN/IEC 61000-3-3.

Decide the length and size of the power supply cable based on the maximum ampere tabulated above in accordance with the national wiring regulations.

Select the fuse(s) and/or circuit breaker(s) from the types and ratings suitable for the maximum ampere tabulated above in accordance with the national wiring regulations.

An RCD suitable for use with inverters, resistant to high frequency noise, is most suitable. RCD’s intended for protection to include high frequency currents are

unnecessary and should be avoided, as potentially causing nuisance tripping, in this application.

If capacity of power supply circuit and enforcement are not enough, it can causes the electric shock and a

ﬁ

re.

Control wiring

Type

Connection cable between outdoor and indoor unit

Outdoor unit

Max. length

1.5 mm

2

U-36 ~ 71PZ3E5

40 m

WARNING

RISK OF FIRE

JOINING OF WIRES MAY

CAUSE OVERHEATING

AND FIRE.

Do not joint wires.

OR

OR

Indoor Unit

Use complete wire without joining.
Wire connection in this area must follow to national wiring rules.

Indoor Unit

Ssc : Short circuit power

: functional earthing

(for the shielded cable)

This equipment complies with EN/IEC 61000-3-12 provided that the short-circuit power Ssc is greater than or

equals to 2 kVA at the interface point between the user’s supply and the public system. It is the responsibility of

the installer or user of the equipment to ensure; by consultation with the distribution network operator if necessary

that the equipment is connected only to supply with a short-circuit power Ssc greater than or equals to 2 kVA.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 1

20/01/30 10:25:02

«
...
75
76
77
78
79
...
»

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Бренд: Daikin Страницы: 11

Бренд: Daikin Страницы: 12

Бренд: Daikin Страницы: 28

Бренд: Daikin Страницы: 8

Бренд: Daikin Страницы: 12

Бренд: Daikin Страницы: 25

Quaternity FTXG09HVJU

Бренд: Daikin Страницы: 80

Бренд: Daikin Страницы: 32

Бренд: Daikin Страницы: 16

Бренд: Daikin Страницы: 20

Бренд: Daikin Страницы: 390

Бренд: Daikin Страницы: 24

Бренд: Daikin Страницы: 19

Бренд: Daikin Страницы: 20

Бренд: Daikin Страницы: 16

Бренд: Daikin Страницы: 12

Бренд: Samsung Страницы: 10

Бренд: Samsung Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды