Panasonic S-3650PF3E Скачать руководство пользователя страница 278

Страница: 278 / 321

<Procedure of CZ-RTC5B>

Fig. 7-4

1 Keep pressing the

and

buttons

simultaneously for 4 or more seconds.

The “Maintenance func” screen appears on the
LCD display.

2 Press the

button to see each

menu.
If you wish to see the next screen instantly, press
the

button.

Select “8. Detailed settings” on the LCD display
and press the

button.

The “Detailed settings” screen appears on the
LCD display.
Select the “Unit no.” by pressing the

button for changes.

Select the “Code no.” by pressing the

button.

Change the “Code no.” by pressing the

button (or keeping it pressed).

4 Select the “Set data” by pressing the

button.

Select one of the “Set data” by pressing the

button.

Then press the

button.

5 Select the “Unit no.” by pressing the

button and press the

button.

The “Exit detailed settings and restart?” (Detailed
setting-end) screen appears on the LCD display.
Select “YES” and press the

button.

Maintenance func

Sel.

20:30 (THU)

Page [

] Confirm

1. Outdoor unit error data

2. Service contact

3. RC setting mode

4. Test run

Maintenance func

Sel.

20:30 (THU)

5. Sensor info.

6. Servicing check

7. Simple settings

8. Detailed settings

Page [

] Confirm

Detailed settings

Unit no.

Code no.

Set data

3-1

10 0001

20:30 (THU)

Sel.

Detailed settings

Unit no.

Code no.

Set data

0001

20:30 (THU)

Sel.

3-1

Detailed settings

Unit no.

Code no.

Set data

Sel.

20:30 (THU)

0001

[

] Confirm

Detailed settings

Unit no.

Set data

Code no.

ALL

20:30 (THU)

Sel.

0002

and restart?

YES

xit detailed settings

CZ-RTC5B

20:30 (THU)

[ ] START

7-5

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 5

20/01/28 11:22:17

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды