Panasonic S-3650PF3E Скачать руководство пользователя страница 314

Страница: 314 / 321

Preparation:

5. Test Operation

Turn on the circuit breaker of units and then turn the power on. After the power is turned on, infrared remote controller operation is ignored for

approx. 1 minute because setting is being made. This is not malfunction. (Contents received while setting are disabled.)

ATTENTION

●

1 Press and hold the emergency operation button for 10 seconds.

2 The indication lamps (OPERATION, TIMER, STANDBY) blink during test operation.

3 To fi nish test operation, press and hold the emergency operation button for 10 seconds.

●

Do not use this mode for purposes other than the test operation.

(To prevent overload of the units)

●

Read the installation instructions supplied with the units.

The test operation can be performed in Heat or Cool mode.

Temperature cannot be changed.

●

The test operation mode is automatically turned o

ﬀ

in 60 minutes.

(To prevent continuous test operation)
turned on or operation is stopped.

●

Outdoor units do not operate for approx. 3 minutes after the power is

The “Alarm Display” shown in the table below expresses the alarm contents

displayed when the wired remote controller is connected. For how to handle

the alarms, see sec2 “2-5. Contents of Remote Controller Switch Alarm

Display” and sec5 “5-1. Contents of Remote Controller Switch Alarm Display”

Detected contents

Indication lamp on the receiver

Alarm

Display

Blinking

OPERATION TIMER STANDBY

E01–E03,

E08–E14,

E17, E18

Communication error

in the remote controller

circuit



◎



E04–E07,

E15, E16,

E19–E31



Communication error

either in the in/outdoor

operation line or the sub-

bus of the outdoor unit

◎

P09–P14

Operation of indoor

protection device

P01,



◎

Alternately

Operation of outdoor

protection device

P15–P31

P02–P08,

◎



Alternately

Error in the indoor

thermistor

F01–F03,

F10–F11

Alternately

◎



Error in the outdoor

thermistor

F04–F09,

F12–F28

Alternately

Error in the indoor EEPROM

◎



F29

Simultaneously

Error in the outdoor EEPROM

◎



F30, F31

Simultaneously

◎



H01–H31

Error related to the

compressor



Error in indoor settings

◎



L01–L03,

L05–L09

◎



Simultaneously

Error in outdoor settings L04,

L10–L31

◎



◎

Simultaneously

A01–A31

Error in the gas heat

pump air conditioner



◎

Simultaneously



◎

Inconsistency in Cooling/Heating

(Including an auto-temp setting for

a model without auto-temp settings)

◎

Alternately

Oil alarm (Same as operation of

outdoor protection device)

◎



Alternately

Auto addressing in progress

(when it is performed with an

infrared remote controller)

Sequentially

◎

Test operation

Simultaneously

◎



: OFF



: ON (Illuminated)

◎

: Blinking (0.5 seconds interval)

Self-diagnostics table and detected contents

8-3-5

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 5

20/01/14 10:04:21

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды