Panasonic S-3650PF3E Скачать руководство пользователя страница 211

Страница: 211 / 321

4-6

4-5. Automatic Heating/Cooling Control

①

The operating mode is selected according to the set temperature and room temperature when the

operation is started.
Room temperature > set temperature in remote controller – 1˚C

→

Cooling mode

Room temperature < set temperature in remote controller – 1˚C

→

Heating mode

②

The set temperature is corrected according to the operating mode. The correction temperature is +2

degrees in cooling mode and -2 degrees in heating mode at the time of factory shipment.

The correction value is different depending on the model. See “4-11. Parameter” for details.

Corrected cooling temperature – control temperature for cooling
Corrected heating temperature – control temperature for heating

When setting temperature in remote controller is 20˚C in the cooling mode (at shipment) :

Control temp. for cooling

22˚C

Set temp. in remote controller 20˚C

Control temp. for heating

18˚C

③

Condition for mode change

Heating

→

Cooling: Room temperature > Control temperature for c 0.5 degree

Cooling

→

Heating: Room temperature < Control temperature for heating -1.0 degree

When setting temperature in remote controller is 20˚C in the cooling mode :

Heating

Heating thermostat OFF Cooling

Cooling thermostat OFF

Heating

continues for 10

minutes regardless

of temp. condition.

Then, the mode

changes to cooling.

The heating

thermostat OFF

continues for 10

minutes regardless

of temp. condition.

Then, the mode

changes to heating.

The cooling

thermostat OFF

Set temp. in remote controller

Control temp. for cooling

+2deg

Control temp. for heating

+2.5deg

Temp. for switching to cooling

Temp. for switching to heating

-2deg

-3deg

Heating thermostat OFF temp.

-1deg

Cooling thermostat OFF temp. +1deg

For settings at the time of factory shipment, see the section “4-11. Parameter”.

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 6

2020/01/30 13:58:47

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды