Panasonic S-3650PF3E Скачать руководство пользователя страница 300

Страница: 300 / 321

Hold the remote controller with your hand and point its transmitter at the receiver.

Power: Turn on the circuit breaker beforehand, referring to the operating instructions for the unit.

1. Press .

2. Press to select the operation mode.

• Every time you press , it cycles from “Auto → Heat

→ Dry → Cool → Fan ”.

• Models that only provide the cooling function cannot operate

in the Auto or Heat mode.

• The available functions differ depending on the indoor unit

being used. See page 8

-2-1-

10 for how to change the operation

mode display.

3. Press to select the fan speed.

• Every time you press , it cycles from “ → → →

→ → (Auto)”.

• Auto does not work in Fan mode.

• If the unit is not heating very effectively with a fan speed “ ”,

switch the fan speed to “ ” or “ ”.

• The available functions differ depending on the indoor unit

being used.

• “ ” is displayed if the function is not available.

4. Press

to set the temperature.

MAX (°C) MIN (°C)

Auto

Heat

Dry / Cool

•

emperature settings cannot be made in Fan mode.

•

The temperature range that can be set varies depending on the model.

•

The maximum temperature varies depending on the system and operating condition. See page 8-2-1-10 for how

to change the maximum temperature.

5. Press

•

Every time you press

, it cycles

from

“

→

(Swing)

→

(Stop)”.

• If you press again while the flap is swinging, you can stop the flap from swinging and set it in place as

desired.

• When the unit is in heating standby, the flap (up-down wind direction plate) faces upwards.

• The available functions differ depending on the indoor unit being used.

• “ ” is displayed if the function is not available.

•

Never try to manually move the flap (up-down wind direction plate) that is operated by the remote

controller.

Stop: Press

• If you cannot turn the air conditioner off in the normal way, disconnect the power to the indoor unit and contact

the dealer where the product was purchased.

• When the unit is stopped with the remote controller, the fan on the outdoor unit may continue to run for a while.

8-2-1-4. Operation

3
5

< Auto operation >

It heats or cools automatically via the differences between the set temperature and the room temperature.

Auto operation is available only when identical refrigerant system inside all the indoor units or cooling/heating

free-type are under control as 1 group. When using gas heat pump (GHP) air conditioners, contact the dealer

where the product was purchased.

8-2-1-4

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 4

20/01/14 10:04:18

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды