Panasonic S-3650PF3E Скачать руководство пользователя страница 275

Страница: 275 / 321

1 Keep pressing the

and

buttons

simultaneously for 4 or more seconds.

The “Maintenance func” screen appears on the
LCD display.

2 Press the

button to see each

menu.
If you wish to see the next screen instantly, press
the

button.

Select “7. Simple settings” on the LCD display and
press the

button.

The “Simple settings” screen appears on the LCD
display.
Select the “Unit no.” by pressing the

button for changes.

Select the “Code no.” by pressing the

button.

Change the “Code no.” by pressing the

button.

4 Select the “Set data” by pressing the

button.

Select one of the “Set data” by pressing the

button.

Then press the

button.

5 Select the “Unit no.” by pressing the

button and press the

button.

The “Exit simple settings and restart?” (Simple
setting-end) screen appears on the LCD display.
Select “YES” and press the

button.

<Procedure of CZ-RTC5B>

Fig. 7-2

Maintenance func

Sel.

20:30 (THU)

Page [

] Confirm

1. Outdoor unit error data

2. Service contact

3. RC setting mode

4. Test run

Maintenance func

Sel.

20:30 (THU)

5. Sensor info.

6. Servicing check

7. Simple settings

8. Detailed settings

Page [

] Confirm

Simple settings

Unit no.

Code no.

Set data

3-1

0001

20:30 (THU)

Sel.

Simple settings

Unit no.

Code no.

Set data

0001

20:30 (THU)

Sel.

3-1

Simple settings

Unit no.

Code no.

Set data

Sel.

20:30 (THU)

0001

[

] Confirm

Simple settings

Unit no.

Set data

Code no.

ALL

20:30 (THU)

Sel.

0002

and restart?

YES

xit simple settings

CZ-RTC5B

20:30 (THU)

[ ] START

7-2

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 2

20/01/28 11:22:15

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды