Panasonic S-3650PF3E Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 321

background image

1

1-9-1

1

1-260

1-9. Intaking Fresh Air of 4-Way cassette Type

Precautions Regarding External Air Intake

1-9-1.

(1) Ventilation Load

Ensure that the design of the air-conditioner takes air-conditioning loads into consideration when external air intake is

involved.

(2) Restrictions on External Air Intake

Ensure that the design conforms to the restrictions on air intake volume stipulated in accordance with the model of

the indoor unit and the intake method. Consideration must also be taken to mixed air content listed in (3) below

without fail.

* If the air intake volume does not satisfy the required ventilation volume, air must be fed into the room separately with

the use of a total heat exchanger or a fresh air processing air-conditioner, etc.

(3) Mixed Air

The amount of external air intake must be set within the scope of the unit’s usage conditions when external air and

internal air is mixed together. This is especially important in the following cases, in which it is necessary to either

feed external air into the room after it has been processed or reduce the amount of external air that is fed in.

1

When the external dew-point temperature is greater than the dry-bulb temperature of the air sucked into the unit

Ensure that processing is performed so that the external dew-point temperature is lower than the temperature of

the air sucked into the unit to prevent the risk of condensation building up.

2

In the case of low external temperatures
There are cases in which the temperature of mixed air is lower than the operating range of the unit if excessive

amounts of external air intake are used when the external temperature is low.

This problem is to be solved by either feeding external air into the room after it has been processed or reducing

the amount of external air that is fed in.

3

When used in combination with humidifiers
External air must always be processed when the external air temperature reaches freezing point to prevent the

risk of the humidifier freezing.

(4) Arranging Ducts and Filters in the Field

External air intake ducting must be arranged in the field.

External air filters must also be installed without fail in order to

prevent the intake of dust and grit.

(5) Thermal Insulation for Ducts

Ensure that all external air intake ducting is heat-insulated

without fail. Failure to observe this may result in the build-up

of condensation.

(6) External Air Intake Coupling

Ensure that the design for external air intake is coupled with

the fan blower operations of the indoor unit.

There are cases in which the dust that accumulates in the

filter is blown into the room if the external air is fed from the

filter. There are also cases in which the noise of external air

being fed into the room can be heard from the indoor unit if

external air is forcibly fed when the booster fan or other

components on the indoor unit are not operating.

(7) Booster Fan Selection

Select the booster fan in accordance with the resistance of

the external air intake duct (diagram on the pressure loss

characteristics of the air flow volume for flexible cylindrical

ducts) and the resistance prevalent inside the unit (external

air intake volume & resistance within unit / operation noise

characteristics).

Regarding the installation direction of the external air intake

duct, refer to the Installation Instructions provided with the

external air intake duct.

(8) Attaching the External Air Intake Flange

ø100

ø150

ø125

Airflow (m

3

/h)

Pressure Loss (Pa)/Mete

r

Flexible Cylindrical Duct

Air Flow Volume for Flexible Cylindrical

Duct-Pressure Loss

30 50

100

200

400 500

300

30
20

10

0.8

0.6
0.4

0.2

0.1

6
4

2

1

1-9. Fresh Air Intake

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 1

20/01/30 10:24:51

«
...
59
60
61
62
63
...
»

Содержание S-3650PF3E


































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для S-3650PF3E

Бренд: GE Страницы: 72

Бренд: Haier Страницы: 122

Бренд: Samsung Страницы: 52

Бренд: Daikin Страницы: 12

DUCT09HP230V1BD

Бренд: Gree Страницы: 24

Super Multi NX FHQ35BVV1B

Бренд: Daikin Страницы: 19

Бренд: Hiyasu Страницы: 14

Бренд: EarthLinked Страницы: 16

C*ED060A Series

Бренд: Unitary products group Страницы: 24

DOM413 BL-198DLR

Бренд: Livoo Страницы: 10

Бренд: KeepRite Страницы: 15

Бренд: Quietside Страницы: 26

NTC5/GNJ Series

Бренд: ICP Страницы: 16

Precedent WSC072E

Бренд: Ingersoll-Rand Страницы: 68

Бренд: Toyotomi Страницы: 48

Бренд: dirna Bergstrom Страницы: 72

Бренд: Acson Страницы: 92

V-Design HCNI 262 ZA

Бренд: Hokkaido Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды