Panasonic S-3650PF3E Скачать руководство пользователя страница 183

Страница: 183 / 321

2-3-1-2

(1)

2-3-1-4. Test Run Using the Remote Controller
CZ-RTC5B (High-spec wired remote controller)

Keep pressing the

and

buttons

simultaneously for 4 or more seconds.
The “Maintenance func” screen appears on the LCD display.

Maintenance func

Sel.

20:30 (THU)

1. Outdoor unit error data

2. Service contact

3. RC setting mode

4. Test run

Page [

] Confirm

Change the display from “OFF” to “ON” by pressing the

button. Then press the

button.

[

] Confirm

Test run

Change

20:30 (THU)

Test run

20:30 (THU)

[ ] START

CZ-RTC5B

If you wish to see the next screen instantly, press the

(2) Press the

or button to see each menu.

button.

Select “4. Test run” on the LCD display and press the

button.

Maintenance func

Sel.

Page [

] Confirm

20:30 (THU)

1. Outdoor unit error data

2. Service contact

3. RC setting mode

4. Test run

CZ-RTC4 (Timer remote controller)

Press the remote controller

(1)

button for 4 seconds or longer.

Then press the

button.

“

” appears on the LCD display while the test run is in progress.

The temperature cannot be adjusted when in Test Run mode.

(This mode places a heavy load on the machines. Therefore use it

only when performing the test run.)

operation modes.

(2) The test run can be performed using the HEAT, COOL, or FAN

NOTE

The outdoor units will not operate for approximately 3 minutes after

the power is turned ON and after operation is stopped.

(1)

(4)

(3) If correct operation is not possible, a code is displayed on the remote

controller LCD display.(Regarding the alarm contents,

see section “2-3-1-5. Contents of Remote Controller Switch Alarm Display”)

(4) After the test run is completed, press the

button again.

Check that “

” disappears from the LCD display.

(To prevent continuous test runs, this remote controller includes a timer function that cancels the test run

after 60 minutes.)

* If the test run is performed using the wired remote controller, operation is possible even if the cassette-type

ceiling panel has not been installed. (“P09” display does not occur.)

CZ-RTC4

(3) Press the

on the LCD display.

button. “TEST” will be displayed

[ ] START

20:30 (THU)

TEST

(4) Press the

button. Test run will be started.

Test run setting mode screen appears on the LCD

display.

FAN SPEED

FLAP

20:30 (THU)

COOL

TEST

FAN SPEED

FLAP

20:30 (THU)

COOL

TEST

Type U3

Type F3

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 2

2020/01/29 19:52:15

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды