Panasonic S-3650PF3E Скачать руководство пользователя страница 313

Страница: 313 / 321

2. Settings

SM830256-00_Single_欧州小筺体 TD&SM.indb 16

16/12/28 13:40:31

Setting for Receiver

Screw

PCB cover

Receiver PCB

Main/Sub selector

switch for remote

controllers (4)*

OFF: Main

ON: Sub
Set its address

(1) to (3)

All set at OFF

when shipped

from the factory.

1 2 3 4

Check the settings of the [S003] DIP switch on the

receiver’s PCB.
* Remove the cover from the receiver when

* When using the infrared remote controller and

the wired remote controller in combination,

set the wired remote controller to [Main].

performing the PCB settings.

Setting Address Switches

When more than 1 receiver is installed in the same room, setting addresses prevents interference.

For how to change addresses of wireless (infrared) remote controllers, see “Matching Up Addresses” of wireless (infrared)

remote controllers on page 8-2-1-8.

To change the receiver’s address, remove the cover from the receiver’s PCB and set No.1 to No.3 of the [003] DIP switch

on PCB.

Remote

Controller

Address

Display

Address

ON/OFF

States

ALL

Position of

the receiver’s

address

switch

Receipt is

possible at

all of the

address

positions

1 2 3 4

OFF ON

8-3-2. CZ-RWRU3, CZ-RWRU3W
1. Accessories

Supplied accessories

(1)

Instructions

Operating

(1)

Installation

Instructions

3. Wiring the Receiver

Wiring Diagram

Sec8.indd 17

2012/02/28 16:14:02

SM830256-00_Single_欧州小筺体 TD&SM.indb 17

16/12/28 13:40:31

CN001

Receiver PCB

Indoor unit

Terminals for RC

wiring

2P white

How to Connect the Wires

•

Connect the wires from the receiver to the terminals for RC wiring on the indoor unit. (No polarity)

4. Installing the Receiver



The receiver can be installed only on the corner shown in

Fig. A. Consider the direction where the panel is attached

to the indoor unit.

Remove the air inlet grille

Indoor unit electric component box

Installation position for receiver (Fig. A)

Fig. A

Indoor unit electric component box

Air Inlet grille

Remove the corner cover

①

Remove the screw fixing the corner cover.

Screw

Corner cover

Convex part

②

Place a hand on both the right and left convex parts of

the corner cover to remove it.

Wire the receiver

①

Hang the string of the receiver on the pin of the ceiling panel.

Receiver

String

②

Pass the wiring from the wireless receiver section into the slit.

(See “Wiring for the receiver”)

③

Fix the wiring with the clamper (supplied) while leaving enough

length of wiring to remove the receiver.

Slit

Fix with the clamper (supplied).

(a) Cut this clamper.

Fix the receiver

①

Fit the receiver to the ceiling panel so the 5 claws are properly

set, and fix it with the removed screw.

•

Make sure the wire is not caught.

•

When attaching the filter chamber, cut the clamper (a), and

attach the receiver.

Refer to the installation instructions

supplied with the panel.

•

Corner cover

Ceiling panel

Convex part

8-3-4

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 4

20/01/14 10:04:21

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды