Panasonic S-3650PF3E Скачать руководство пользователя страница 304

Страница: 304 / 321

2. Press

ADR

to select the address of the receiver you want to

control, and press

•

Every time you press

ADR

, it cycles from “ALL (All the addresses)

→

6”.

•

If it corresponds to the receiver’s address setting, the buzzer sounds.

Note

•

Set the address of the receiver as instructed in the operating instructions of your

receiver. Do not set by yourself. Contact the dealer where the product was

purchased.

■

For wall mounted type indoor unit

< Setting the address of the indoor unit >

1. Press [Emergency Operation] of the indoor unit for 4 seconds or longer.

• OPERATION lamp, TIMER lamp, and then STANDBY lamp repeatedly light one after the other for 1 second

each to indicate the unit is ready for address setting.

Checking Addresses

1. Press with one end of an unfolded paper clip

(or a similar object that can fit).

• Its current address appears on the display for 5 seconds.
• If this address corresponds to the address of a receiver, the buzzer

sounds. (If it is on ALL, the buzzer will always sound.)

• If it is on ALL, it can be operated regardless of receiver addresses.
Point the remote controller at the receiver you wish to operate and

transmit.

ADR

Matching Up Addresses

■

If not wall mounted type indoor unit

< Setting Remote Controller Addresses >
1. Press with one end of an unfolded paper clip

(or a similar object that can fit) for 4 seconds or longer.

• The current address number starts blinking.

ADR

Address

1, 2

Address

< Setting Remote Controller Addresses >

2. Set the address for the remote controller following the procedure under the section

“

■

If not wall mounted type indoor unit” (see this section noted above).

• Repeat Step 2 under “

■

If not wall mounted type indoor unit” if you are setting more units.

• The address setting ready status of the indoor unit ends if data transmission is not received from the remote

controller for 3 minutes.

• Press [Emergency Operation] on the receiver to end the address setting ready status of the indoor unit.

8-2-1-8

SM830283-00_欧州向け R32シングル36-71形TD&SM.indb 8

20/01/14 10:04:19

Содержание S-3650PF3E


































































































































































































































































































































Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды

Panasonic S-3650PF3E, Технические данные и руководство по обслуживанию

Результаты поиска

Содержание S-3650PF3E

Отзывы:

Похожие инструкции для S-3650PF3E

Бренды по названию

Популярные бренды