Renesas H8S/2158 User Manual Download Page 406 | Manualshive

Page: 406 / 929

background image

Section 14 Timer Connection

Rev. 3.00 Jan 25, 2006 page 352 of 872
REJ09B0286-0300

14.3.2

Timer Connection Register O (TCONRO)

TCONRO controls output signal output, phase inversion, etc.

Bit

Bit Name

Initial Value

R/W

Description

7
6
5
4

HOE
VOE
CLOE
CBOE

0
0
0
0

R/W
R/W
R/W
R/W

Output Enable
These bits control enabling/disabling of output of
horizontal synchronization signal (HSYNCO),
vertical synchronization signal (VSYNCO), clamp
waveform (CLAMPO), and blanking waveform
(CBLANK) output. When output is disabled, the
state of the relevant pin is determined by port DR
and DDR, FRT, TMR, and PWM settings.
Output enabling/disabling control does not affect the
port, FRT, or TMR input functions, but some FRT
and TMR input signal sources are determined by the
SCONE bit in TCONRI.

HOE:
0: The P43/TMO1/HSYNCO pin functions as the

P43/TMO1 pin

1: The P43/TMO1/HSYNCO pin functions as the

HSYNCO pin

VOE:
0: The P61/FTOA/VSYNCO pin functions as the

P61/FTOA pin

1: The P61/FTOA/VSYNCO pin functions as the

VSYNCO pin

CLOE:
0: The P64/FTIC/CLAMPO pin functions as the

P64/FTIC pin

1: The P64/FTIC/CLAMPO pin functions as the

CLAMPO pin

CBOE:
0: The P66/FTOB/CBLANK pin functions as the

P66/FTOB pin

1: The P66/FTOB/CBLANK pin functions as the

CBLANK pin

«
...
404
405
406
407
408
...
»

Summary of Contents for H8S/2158


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2158

Brand: D-Link Pages: 38

Web Smart DES-1210-28P

Brand: D-Link Pages: 6

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 23

Express EtherNetwork DI-604

Brand: D-Link Pages: 7

xStack Storage DSN-4000 Series

Brand: D-Link Pages: 97

Brand: Ebyte Pages: 8

Brand: Paradyne Pages: 1

TWR-SB0410-36EVB

Brand: NXP Semiconductors Pages: 26

Brand: Amplifier Tech Pages: 36

Brand: Delta Pages: 2

ER3-100 (5K02-55)

Brand: 8e6 Technologies Pages: 74

Brand: CAP-XX Pages: 8

Brand: Velopex Pages: 7

SUPERLOADER DLT MAGAZINE

Brand: Tandberg Data Pages: 6

PARTNER PC CARD

Brand: Avaya Pages: 4

Extreme Gaming VGA Cooler GV1000

Brand: ZALMAN Pages: 7

Brand: ATI Technologies Pages: 87

Brand: Xcellon Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands