Renesas H8S/2158 User Manual Download Page 421 | Manualshive

Page: 421 / 929

background image

Section 14 Timer Connection

Rev. 3.00 Jan 25, 2006 page 367 of 872

REJ09B0286-0300

14.4.6

Internal Synchronization Signal Generation (IHG/IVG/CL4 Signal Generation)

By using the timer connection facility, FRT, and TMR_Y, it is possible to automatically generate
internal signals (IHG and IVG signals) corresponding to the IHI and IVI signals. As the IHG
signal is synchronized with the rise of the IVG signal, the IHG signal period must be made a
divisor of the IVG signal period in order to keep it constant. In addition, the CL4 signal can be
generated in synchronization with the IHG signal.

The contents of OCRA in the FRT are updated by the automatic addition of the contents of
OCRAR or OCRAF, alternately, each time a compare-match occurs. A value corresponding to the
0 interval of the IVG signal is written in OCRAR, and a value corresponding to the 1 interval of
the IVG signal is written in OCRAF. The IVG signal is set by a compare-match after an OCRAR
addition, and reset by a compare-match after an OCRAF addition.

The IHG signal is the TMR_Y timer output. TMR_Y is set to count internal clock pulses, and to
be cleared on a TCORA compare-match, to fix the period and set the timer output. TCORB is set
so as to reset the timer output. The IVG signal is connected as the TMR_Y reset input (TMRI),
and the rise of the IVG signal can be treated in the same way as a TCORA compare-match.

The CL4 signal is a waveform that rises within one system clock period after the fall of the IHG
signal, and has an interval of 1 for 6 system clock periods.

Examples of TCR, TCSR, TCORA, and TCORB settings in TMR_Y, and TCR, OCRAR,
OCRAF, and TOCR settings in the FRT are shown in table 14.9, and the IHG signal/IVG signal
timing chart is shown in figure 14.8.

«
...
419
420
421
422
423
...
»

Summary of Contents for H8S/2158


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2158

Brand: Barracuda Networks Pages: 2

Brand: Direct IP Pages: 76

PCard-E 021L-D5 Series

Brand: ORiNG Pages: 2

Brand: Cypress Semiconductor Pages: 19

DUAL Nx56/64 1200142L1#

Brand: ADTRAN Pages: 48

Brand: Agilent Technologies Pages: 458

Brand: Curtiss-Wright Pages: 12

Brand: Curtiss-Wright Pages: 58

4 Channel Fan Speed Control Module CLX-1FAN4

Brand: Crestron Pages: 1

Brand: Johnson Controls Pages: 40

Coral FlexiCom 6000

Brand: Tadiran Telecom Pages: 340

EK-Quantum Vector2 Trio RTX 3080/90 ABP Set D-RGB

Brand: ekwb Pages: 18

Brand: ekwb Pages: 2

EK-FC WX9100 PRO BACKPLATE

Brand: ekwb Pages: 10

EK-Classic Pump Reservoir 160 SPC PWM D-RGB

Brand: ekwb Pages: 8

Brand: Altera Pages: 78

Brand: Raypak Pages: 18

Brand: ENHANCED VISION Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands