Renesas H8S/2158 User Manual Download Page 543 | Manualshive

Page: 543 / 929

background image

Section 17 I

2

C Bus Interface (IIC)

Rev. 3.00 Jan 25, 2006 page 489 of 872

REJ09B0286-0300

Bit

Bit Name

Initial Value R/W

Description

Clocked synchronous serial format mode:

•

At the end of data transfer (rise of the 8th

transmit/receive clock with serial format selected)

•

When a start condition is detected with serial format

selected

When the ICDRE or ICDRF flag is set to 1 in any
operating mode:

•

When a start condition is detected in transmit mode

(when a start condition is detected in transmit mode
and the ICDRE flag is set to 1)

•

When data is transferred among the ICDR register

and buffer (when data is transferred from the transmit
buffer to the shift register in transmit mode and the
ICDRE flag is set to 1, or when data is transferred
from the shift register to the receive buffer in receive
mode and the ICDRF flag is set to 1)

[Clearing conditions]

•

When 0 is written in IRIC after reading IRIC = 1

•

When ICDR is read from or written to by the DTC

(This may not function as a clearing condition
depending on the situation. For details, see the
description of the DTC operation given below.)

Note:

*

Only 0 can be written, to clear the flag.

When the DTC is used, the IRIC flag is cleared automatically and transfer can be performed
continuously without CPU intervention.

When, with the I

2

C bus format selected, the IRIC flag is set to 1 and an interrupt is generated,

other flags must be checked in order to identify the source that set the IRIC flag to 1. Although
each source has a corresponding flag, caution is needed at the end of a transfer.

When the ICDRE or ICDRF flag is set, the IRTR flag may or may not be set. The IRTR flag (the
DTC start request flag) is not set at the end of a data transfer up to detection of a retransmission
start condition or stop condition after a slave address (SVA) or general call address match in I

2

C

bus format slave mode.

Even when the IRIC flag and IRTR flag are set, the ICDRE or ICDRF flag may not be set. The
IRIC and IRTR flags are not cleared at the end of the specified number of transfers in continuous
transfer using the DTC. The ICDRE or ICDRF flag is cleared, however, since the specified
number of ICDR reads or writes have been completed. Table 17.4 shows the relationship between
the flags and the transfer states.

«
...
541
542
543
544
545
...
»

Summary of Contents for H8S/2158


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for H8S/2158

Brand: 3Com Pages: 16

Brand: Cypress Semiconductor Pages: 11

Brand: Renesas Pages: 2

PBE-5AC-300-ISO

Brand: Ubiquiti Pages: 28

SABVISION NVR32

Brand: SAB Pages: 29

Brand: XJTAG Pages: 9

Brand: Xilinx Pages: 8

Brand: H3C Pages: 9

PowerMatch ESPLink

Brand: Bose Pages: 2

LEDWALL Optimizer HQ P2

Brand: Gundermann VIDEOWALL Pages: 12

Brand: ICP DAS USA Pages: 31

Brand: AXIOMTEK Pages: 2

Brand: ADS Technologies Pages: 1

Brand: CSL Pages: 24

X570 AORUS ELITE WIFI

Brand: Gigabyte Pages: 48

Brand: Boser Pages: 54

OPTI495XLC VL-BUS 3/486

Brand: A-Trend Pages: 16

Brand: Iomega Pages: 32

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands