Renesas H8S/2158 User Manual Download Page 667

Page: 667 / 929

Section 18 Universal Serial Bus Interface (USB)

Rev. 3.00 Jan 25, 2006 page 613 of 872

REJ09B0286-0300

USB Host

USB Function Core

Slave CPU

Core Interface

Notes: 1. When an EP5TF interrupt is specified as a USBIB or USBIC interrupt according to the INTSELR0 setting, the corresponding interrupt

occurs. In this case, if a USBIB or USBIC interrupt occurs, interrupt source determination process is not required. (Note that TFFR0 must

be accessed to clear the flags.)

2. When an EP5TS interrupt is specified as a USBIB or USBIC interrupt according to the INTSELR0 setting, the corresponding interrupt

occurs. In this case, if a USBIB or USBIC interrupt occurs, interrupt source determination process is not required. (Note that TSFR0 must

be accessed to clear the flags.)

Receive an OUT

token packet

Receive a NAK

handshake packet

Send NAK to the host CPU

Send NAK to the slave CPU

Request to rewind the

RFU pointer

Request an USBID

interrupt (EP5TF)

Request RFU transmission

A RAM-FIFO full error

occurs

Initiate the USBID interrupt

processing

Read USBIFR0 and check

if a TF interrupt occurs

or not

Read TFFR0 and check

if an EP5TF interrupt occurs

or not

Read data and modify

the RFU pointer

Clear the EP5TF bit of

TFFR0 to 0

Complete the USBID

interrupt processing

Send an OUT

token packet

Send an OUT data

packet (64 bytes)

Receive an OUT data

packet (64 bytes)

Receive an ACK

handshake packet

Re-transmission

Send an OUT

token packet

Send an OUT data

packet (64bytes)

Receive an OUT

token packet

Receive an OUT data

packet (64 bytes)

Send ACK to the host CPU

Send ACK to the slave CPU

Write data to the EP5

receive buffer

A RAM-FIFO full error

occurs

Rewind the RFU pointer

and send ACK

Write data to the EP5

receive buffer

Request RFU transmission

Request to modify the RFU

pointer

Request an USBID interrupt

(EP5TS)

Initiate the USBID

interrupt processing

The following procedure is the same

as that when the initial FIFO is empty.

Modify the RFU pointer

and send ACK

Write data to RAM-FIFO

and send ACK

Figure 18.9 Operation on Receiving an OUT Token (EP5-OUT: Initial FIFO Is Full)

Summary of Contents for H8S/2158


































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Search results

Summary of Contents for H8S/2158

Reviews:

Related manuals for H8S/2158

Brands by name

Popular brands

Renesas H8S/2158, User Manual

Search results

Summary of Contents for H8S/2158

Reviews:

Related manuals for H8S/2158

Brands by name

Popular brands