manualshive.com logo in svg

Omron CJ1W-MA - REV 10-2008, Operation Manual

Share
Download
Omron CJ1W-MA - REV 10-2008 Operation Manual Download Page 378

351

Jogging

Section 10-2

Axis Operating Input Memory Areas (Monitoring)

b = Beginning word of Axis Operating Input Areas specified in Common
Para (Axis No. 

− 

1) 

×

 25

The Servo lock status of each axis can be confirmed by checking the SVON
Flag in the Axis Operating Input Memory Areas.

Timing Chart

The following timing chart is for when SERVO LOCK and SERVO UNLOCK
are executed.

10-2 Jogging

10-2-1 Overview of Operation

The axis travels in the specified direction at the specified speed while the JOG
Bit is ON, and decelerates to a stop when the JOG Bit turns OFF. Jogging
operations can be executed even if the origin has not been established.

10-2-2 Procedure for Jogging Operations

The procedure for using jogging is as follows:

1,2,3...

1.

Set the Common Parameters and save them.

2.

Turn ON the PCU again or restart the Unit.
The data for the Common Parameters set in step 1 above is enabled.

3.

Start MECHATROLINK communications.

Name

Word

Bits

Contents

Receiving Command 
Flag

b

00

0: Command reception enabled.

0 

→

 1: Command reception started.

1: Receiving command (command 
reception disabled).

Error Flag

12

0: No axis error

1: Axis error has occurred.

Busy Flag

13

1: Axis busy (axis operation executing).

SVON (Servo ON) Flag

b+1

03

0: Servo unlocked.

1: Servo locked.

SERVO LOCK 
(word a+1, bit 00)

SERVO UNLOCK 
(word a+1, bit 01)

PCU Positioning Completed 
Flag (word b, bit 05)

No Origin Flag 
(word b, bit 06)

Busy Flag (word b, bit 13)

Servo ON (SVON) Flag 
(word b+1, bit 03)

a = Beginning word of Axis Operating Output Areas specified in Common Para (Axis No. 

−

1) 

×

 25

b = Beginning word of Axis Operating Input Areas specified in Common Para (Axis No. 

−

1) 

×

 25

When SERVO UNLOCK is executed, 
the PCU Positioning Completed Flag 
turns OFF. 

The status of the No Origin Flag and 
Stop Execution Flag do not change 
when SERVO UNLOCK is executed. 

The SVON Flag turns ON/OFF when 
the processing at the Servo Drive is 
finished (e.g., reading absolute 
encoder data, turning ON brake).

STOP Execution Flag 
(word b, bit 15)

For details on the flag operations when using Servomotors with absolute encoders, 
refer to 

8-6-6 Establishing the Origin Using an Absolute Encoder

. 

Summary of Contents for CJ1W-MA - REV 10-2008





































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands