manualshive.com logo in svg

Omron CJ1W-MA - REV 10-2008, Operation Manual

Share
Download
Omron CJ1W-MA - REV 10-2008 Operation Manual Download Page 214

187

Axis Operating Input Memory Areas

Section 4-8

Example: Executing RELATIVE MOVEMENT COMMAND.

The PCU Positioning Completed Flag will not turn ON when axis operation
stops under the following conditions.

• Stops due to an error during positioning.

• Stops due to DECELERATION STOP or EMERGENCY STOP sent during

positioning.

• Jogging (JOG) stops.

The PCU Positioning Completed Flag will also not turn ON when axis opera-
tion stops during positioning due to DECELERATION STOP or EMERGENCY
STOP, even if the position is within the 

Positioning Completion Range 1

 speci-

fied for the original target position. 

The PCU Positioning Completed Flag will turn OFF when the power is turned
ON, a connection is released, another axis operation is started successfully
(including jogging, speed control, and torque control), or Servo Unlock is exe-
cuted.

Note

On machines for which position deviation occurs between the feedback posi-
tion and target position (command position) when the axis is stopped, such as
pushing a load or using a vertical axis, the PCU Positioning Completed Flag
will not turn ON if the set value for the 

Positioning Completion Range 1

 is too

small. Adjust the set value for the 

Positioning Completion Range 1

 to suit the

operating conditions for the machine.

Position (a+2,a+3)

Speed (a+4,a+5)

RELATIVE MOVEMENT 
command (a 04)

Speed

Receiving Command 
Flag (b 00)

PCU Positioning 
Completed Flag (b 05)

2710 hex (10000)

3E8 hex (1000)

Target speed: 1000 
(command units/s)

Travel distance 
10000 (command 
unit)

Solid line: Command speed

Broken line: Feedback speed

Time

The Receiving Command Flag remains 
ON for at least one cycle time after the 
positioning command is received. 

The PCU Positioning Completed Flag is turned OFF 
when a movement command is executed. 
The PCU Positioning Completed Flag is turned ON when 
the number of the Servo Drive's deviation counter 
residual pulses is less than the value set for the 
positioning completion range. Depending on the number 
of deviation counter residual pulses when pulse output 
has been completed, a delay may occur in the time 
between when the pulse output from the Position Control 
Unit is completed until positioning has been completed. 

Summary of Contents for CJ1W-MA - REV 10-2008





































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands