D-Link DES-3326SRM Page 37 Command Line Interface Reference Manual Download | Manualshive

Page: 37 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Basic Switch Commands

37

enable telnet

Purpose

Used to enable communication with and
management of the switch using the Telnet
protocol.

Syntax

enable telnet <tcp_port_number>

Description

This command is used to enable the Telnet
protocol on the switch. The user can specify
the TCP or UDP port number the switch will
use to listen for Telnet requests.

Parameters

<tcp_port_number>

−

The TCP port number.

TCP ports are numbered between 1 and
65535. The

“

well-known

”

TCP port for the

Telnet protocol is 23.

Restrictions

Only administrator-level users can issue
this command.

Example Usage:

To enable Telnet and configure port number:

DES-3326SR:4#enable telnet 23
Command: enable telnet 23

Success.

DES-3326SR:4#

«
...
35
36
37
38
39
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Brand: Quick Pages: 28

Brand: Quintum Pages: 2

Brand: ORiNG Pages: 2

Brand: LOVATO ELECTRIC Pages: 37

Brand: Fairchild Pages: 19

TurboIron 24X series

Brand: Brocade Communications Systems Pages: 82

Brand: Omega Pages: 17

Brand: ATEN Pages: 21

Brand: Gefen Pages: 9

Brand: Lancom Pages: 71

Brand: Videosec Pages: 3

Brand: Wantec Pages: 4

Brand: CYP Pages: 72

Brand: coval Pages: 2

Brand: SolidView Pages: 39

True Scale Fabric 12000 Series

Brand: Intel Pages: 125

Brand: Microsens Pages: 11

Brand: Dahua Pages: 17

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands