manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

Link Aggregation Commands 

187 

 

17 

L

INK 

A

GGREGATION 

C

OMMANDS

 

The  link  aggregation  commands  in  the  Command  Line  Interface 
(CLI)  are  listed  (along  with  the  appropriate  parameters)  in  the 
following table. 

 

Command 

Parameters 

create 
link_aggregation  

group_id <value> 

delete 
link_aggregation 

group_id <value> 

config 
link_aggregation 

group_id <value> 
master_port <port> 
ports <portlist> 
state [enabled/disabled] 

config 
link_aggregation 
algorithm 

mac_source 
mac_destination 
mac_source_dest 
ip_source 
ip_destination 
ip_source_dest 

show 
link_aggregation 

group_id <value> 
algorithm 

Each command is listed, in detail, in the following sections. 

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Hama S2100 Manual preview
S2100
Brand: Hama Pages: 9
N-Tron 900 Installation & User Manual preview
900
Brand: N-Tron Pages: 18
Camozzi CSD Series Use And Maintenance Instructions preview
CSD Series
Brand: Camozzi Pages: 2
H3C S5800-EI Series Installation Manual preview
S5800-EI Series
Brand: H3C Pages: 61
Aruba Instant On 1930 24G 4SFP/SFP+l Installation And Getting Started Manual preview
Instant On 1930 24G 4SFP/SFP+l
Brand: Aruba Pages: 48
hager TS 204 User Instruction preview
TS 204
Brand: hager Pages: 2
Hanwell IKVM-101Plus User Manual preview
IKVM-101Plus
Brand: Hanwell Pages: 109
Olympia TV 150 Quick Start Manual preview
TV 150
Brand: Olympia Pages: 6
Tekmar tekmarNet4 User Switch 480 Data Brochure preview
tekmarNet4 User Switch 480
Brand: Tekmar Pages: 8
Oehlbach UltraHD Switch 3:1 User Manual preview
UltraHD Switch 3:1
Brand: Oehlbach Pages: 20
Qlogic SANbox 5000 Series Instructions preview
SANbox 5000 Series
Brand: Qlogic Pages: 2
Clas Ohlson EMT445PCS Instruction Manual preview
EMT445PCS
Brand: Clas Ohlson Pages: 4
ddtop UQK-400 Operation Manual preview
UQK-400
Brand: ddtop Pages: 10
ELPRO TZ04 Installation And Use Manual preview
TZ04
Brand: ELPRO Pages: 8
ANTAIRA LMX-1002G-SFP Series Hardware Manual preview
LMX-1002G-SFP Series
Brand: ANTAIRA Pages: 22
Cumberland PowerTrak Installation preview
PowerTrak
Brand: Cumberland Pages: 2
G&D DVIMUX8-USB Installation And Operation Manual preview
DVIMUX8-USB
Brand: G&D Pages: 80
HighSecLabs K304 Quick Start Manual preview
K304
Brand: HighSecLabs Pages: 2

Brands by name

Popular brands

Load more brands