manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

Bootp Relay Commands 

261 

 

 

show bootp_relay 

Purpose 

Used  to  display  the  current  BOOTP  relay 
configuration. 

Syntax 

show bootp_relay {ipif <ipif_name>} 

Description 

This  command  will  display  the  current 
BOOTP  relay  configuration  for  the  switch,  or 
if  an  IP  interface  name  is  specified,  the 
BOOTP  relay  configuration  for  that  IP 
interface. 

Parameters 

<ipif_name> 

−

  The  name  of  the  IP  interface 

for  which  you  what  to  display  the  current 
BOOTP relay configuration. 

Restrictions 

none. 

Example Usage: 

To display bootp relay status. 

   

DES-3326SR:4#show bootp_relay ipif System 
Command: show bootp_relay ipif System 
Bootp Relay Status                    :Disabled 
Bootp Hops Count Limit           :4 
bootp Relay Time Threshold    :0 
Interface         Server 1          Server 2           Server 3          Server 4  
-------------     ---------------     ----------------      ---------------        -------------- 
  System    10.48.74.122     10.23.12.34     10.12.34.12    10.48.75.121 
 
Total Entries: 1 
 
DES-3326SR:4#

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

I-Tech M118 User Manual preview
M118
Brand: I-Tech Pages: 27
4B M800 Elite Series Operation Manual preview
M800 Elite Series
Brand: 4B Pages: 12
Gefen EXT-DVI-441DL User Manual preview
EXT-DVI-441DL
Brand: Gefen Pages: 31
ORiNG IGS-1082GP Quick Installation Manual preview
IGS-1082GP
Brand: ORiNG Pages: 2
Theben TIMEGUARD WF10COM Installation & Operating Instructions Manual preview
TIMEGUARD WF10COM
Brand: Theben Pages: 35
Gefen ToolBox GTB-MHDMI1.3-441 User Manual preview
ToolBox GTB-MHDMI1.3-441
Brand: Gefen Pages: 25
PRO SIGNAL PSG3061 Quick Start Manual preview
PSG3061
Brand: PRO SIGNAL Pages: 4
Scion SC03.4101 Operation Manual preview
SC03.4101
Brand: Scion Pages: 8
S&C Omni-Rupter Series Installation And Operation Manual preview
Omni-Rupter Series
Brand: S&C Pages: 31
Lantech IES-5222T Series User Manual preview
IES-5222T Series
Brand: Lantech Pages: 30
3Com 3CB9E7 - CoreBuilder 9000 Chassis Switch Getting Started Manual preview
3CB9E7 - CoreBuilder 9000 Chassis Switch
Brand: 3Com Pages: 132
Accton Technology EtherHub-24s Quick Installation Manual preview
EtherHub-24s
Brand: Accton Technology Pages: 7
ALFAtron ALF- WUK3A Manual preview
ALF- WUK3A
Brand: ALFAtron Pages: 15
Advantech EKI-2525P User Manual preview
EKI-2525P
Brand: Advantech Pages: 28
A10 Thunder series 930 Installation Manual preview
Thunder series 930
Brand: A10 Pages: 44
Raritan TMCAT17 series Quick Setup Manual preview
TMCAT17 series
Brand: Raritan Pages: 7
W2IIHY 3 4 Operating Manual preview
3 4
Brand: W2IIHY Pages: 28
AMBIENTECH TONE-WS Series Installation Instructions preview
TONE-WS Series
Brand: AMBIENTECH Pages: 4

Brands by name

Popular brands

Load more brands