manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

OSPF Configuration Commands 

309 

 

 
OSPF Area Aggregation Settings 
 
Area ID         Aggregated             LSDB     Advertise 
                     Network Address    Type 
---------------      ------------------       --------     --------- 
 
Total Entries : 0 
 
OSPF Host Route Settings 
 
Host Address    Metric           Area ID         TOS 
---------------             ------     ---------------             --- 
     10.3.3.3                  1           10.1.1.1              0 
 
Total Entries : 1 

 
DES-3326SR:4#

 

 

 
 
 
 
 
 
 

 

 

 

 

create ospf area 

Purpose 

Used to configure OSPF area settings. 

Syntax 

create ospf area <area_id> type 
[normal/stub] {stub_summary 
[enabled/disabled]/metric <value>}] 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

IDK MSD-804FD Series Command Manual preview
MSD-804FD Series
Brand: IDK Pages: 133
IDK MSD-72 Series User Manual preview
MSD-72 Series
Brand: IDK Pages: 150
IDK MSD-501 Command Reference Manual preview
MSD-501
Brand: IDK Pages: 101
IDK MSD-402 Command Reference Manual preview
MSD-402
Brand: IDK Pages: 85
IDK IMP-400UHD Command Reference Manual preview
IMP-400UHD
Brand: IDK Pages: 40
IDK FDX-32 User Manual preview
FDX-32
Brand: IDK Pages: 97
IDK FDX-S Series User Manual preview
FDX-S Series
Brand: IDK Pages: 117
IDK FDX-16 User Manual preview
FDX-16
Brand: IDK Pages: 77
WAGO 852-112/000-001 Manual preview
852-112/000-001
Brand: WAGO Pages: 30
AV-Box WUH5-H2 User Manual preview
WUH5-H2
Brand: AV-Box Pages: 11
DANLERS CESRA PIR 10VDC Installation Notes preview
CESRA PIR 10VDC
Brand: DANLERS Pages: 2
LEGRAND Valena Life LE-752107 User Manual preview
Valena Life LE-752107
Brand: LEGRAND Pages: 5
Avocent AMX Switch Series Installer/User Manual preview
AMX Switch Series
Brand: Avocent Pages: 236
Triax TMS 5XX SE AQ-EU Series User Manual preview
TMS 5XX SE AQ-EU Series
Brand: Triax Pages: 6
Exsys EX-1189HMVS-3 Manual preview
EX-1189HMVS-3
Brand: Exsys Pages: 16
Unifore POE4100P User Manual preview
POE4100P
Brand: Unifore Pages: 8
Quirky R-INS-TAPT-WH02 Installation Instructions preview
R-INS-TAPT-WH02
Brand: Quirky Pages: 2
ATEN ES0152 User Manual preview
ES0152
Brand: ATEN Pages: 300

Brands by name

Popular brands

Load more brands