manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

220

 

Route Redistribution Commands 

 

21 

R

OUTE 

R

EDISTRIBUTION 

C

OMMANDS

 

The  switch  port  commands  in  the  Command  Line  Interface  (CLI) 
are listed (along with the appropriate parameters) in the following 
table. 

Command 

Parameters 

create route 
redistribute dst 
ospf 

src [static/rip/local] 
mettype [1/2] 
metric <value> 

create route 
redistribute dst rip 

src [static/ospf{all/internal/external/ 
type_1/type_2} 
metic <value> 

config route 
redistribute dst 
ospf 

src [static/rip/local] 
mettype [1/2] 
metric <value> 

delete route 
redistribute 

dst [rip/ospf] 
src [local/static/ospf] 

show route 
redistribute 

dst [rip/ospf] 
src [rip/static/local/ospf] 

 

Each command is listed, in detail, in the following sections. 

 

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

D-Link DES-1005E Quick Install Manual preview
DES-1005E
Brand: D-Link Pages: 2
IDEC HS1C Series Instruction Sheet preview
HS1C Series
Brand: IDEC Pages: 5
IDEC HS5E Series Instruction Sheet preview
HS5E Series
Brand: IDEC Pages: 7
Conceptronic HUBBIES 01 Multi Language Quick Manual preview
HUBBIES 01
Brand: Conceptronic Pages: 7
Taiden TMX-0404SDI Installation And Operation Manual preview
TMX-0404SDI
Brand: Taiden Pages: 21
Endress+Hauser Liquipoint FTW33 Operating Instructions Manual preview
Liquipoint FTW33
Brand: Endress+Hauser Pages: 48
hager EHN010 Installation And Instruction Manual preview
EHN010
Brand: hager Pages: 6
Leonton EG2-1600 Series User Manual preview
EG2-1600 Series
Brand: Leonton Pages: 19
Ormazabal velatia cgm.3 system General Instructions Manual preview
velatia cgm.3 system
Brand: Ormazabal Pages: 76
IDT 89HPES12N3 User Manual preview
89HPES12N3
Brand: IDT Pages: 158
Konig KN-HDMIMAT20 Manual preview
KN-HDMIMAT20
Brand: Konig Pages: 52
Gefen HDMI-341 User Manual preview
HDMI-341
Brand: Gefen Pages: 12
Dahua D-PFS3110-8ET1GT1GF-96 Quick Start Manual preview
D-PFS3110-8ET1GT1GF-96
Brand: Dahua Pages: 17
Ev-ent Hire ENTERTAINMENT HUB Instructions preview
ENTERTAINMENT HUB
Brand: Ev-ent Hire Pages: 5
Novy 990.031 Operating Instructions Manual preview
990.031
Brand: Novy Pages: 12
AV Access 4KSW21-L User Manual preview
4KSW21-L
Brand: AV Access Pages: 16
Southern States CBL-T Installation Instructions Manual preview
CBL-T
Brand: Southern States Pages: 32
ATEN ES0152 User Manual preview
ES0152
Brand: ATEN Pages: 300

Brands by name

Popular brands

Load more brands