manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

286

 

DVMRP Commands 

 

 

show dvmrp routing_table 

Purpose 

Used  to  display  the  current  DVMRP  routing 
table. 

Syntax 

show  dvmrp  routing  table  {ipaddress 
<network_address>} 

Description 

The command is used to display the current 
DVMRP routing table. 

Parameters 

<ipif_name> 

−

  The  name  of  the  IP  interface 

for  which  you  want  to  display  the 
corresponding DVMRP routing table. 

ipaddress  <network_address> 

−

  The  IP 

address  and  netmask  of  the  destination.  
You can specify the IP address and netmask 
information  using  the  traditional  format  or 
the 

CIDR 

format. 

 

For 

example, 

10.1.2.3/255.255.0.0 or 10.2.3.4/16.   

Restrictions 

none. 

 

 

 

 

 

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

CALIENT S320 Repair And Diagnostics Field Manual preview
S320
Brand: CALIENT Pages: 22
Panasonic WJSX150 - SWITCHER - ADDENDUM Addendum preview
WJSX150 - SWITCHER - ADDENDUM
Brand: Panasonic Pages: 48
Ubiquiti ES-24-250W Quick Start Manual preview
ES-24-250W
Brand: Ubiquiti Pages: 24
Ubiquiti USW-24 User Manual preview
USW-24
Brand: Ubiquiti Pages: 13
Ubisys ZIGBEE S2(-R) Quick Start Manual preview
ZIGBEE S2(-R)
Brand: Ubisys Pages: 2
WAGO ETHERNET Accessories 852 852-0111 Mounting, Installation And Handling Manual preview
ETHERNET Accessories 852 852-0111
Brand: WAGO Pages: 38
LOVATO ELECTRIC ATL900 Instruction Manual preview
ATL900
Brand: LOVATO ELECTRIC Pages: 37
DAB ESC plus 3M Instruction For Installation And Maintenance preview
ESC plus 3M
Brand: DAB Pages: 56
REV Ritter RF102R Assembly And Operating Instructions Manual preview
RF102R
Brand: REV Ritter Pages: 15
J-Tech Digital JTECH-HD4X48 User Manual preview
JTECH-HD4X48
Brand: J-Tech Digital Pages: 28
Generac Power Systems 004635-3 Owner'S Manual preview
004635-3
Brand: Generac Power Systems Pages: 20
N-Tron NTSFP-LX-40 User Manual & Installation Manual preview
NTSFP-LX-40
Brand: N-Tron Pages: 20
Ametek SIL IntelliPoint RF S*R*L Series Installation And Operating Instructions Manual preview
SIL IntelliPoint RF S*R*L Series
Brand: Ametek Pages: 93
Homefibre OMS 113- 220 User Manual preview
OMS 113- 220
Brand: Homefibre Pages: 2
N-Tron 708M12 User Manual & Installation Manual preview
708M12
Brand: N-Tron Pages: 169
Hama 39859 Operating Instructions Manual preview
39859
Brand: Hama Pages: 14
Cabletron Systems SmartSTACK ETHERNET ELS10-27 User Manual preview
SmartSTACK ETHERNET ELS10-27
Brand: Cabletron Systems Pages: 126
Aruba Instant On 1930 Series Installation, Safety, And Regulatory Information preview
Instant On 1930 Series
Brand: Aruba Pages: 8

Brands by name

Popular brands

Load more brands