manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

Share
Download
D-Link DES-3326SRM Command Line Interface Reference Manual Download Page 61

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

Network Management Commands 

61 

 

show snmp user 

Purpose 

Used  to  display  information  about  each 
SNMP  username  in  the  SNMP  group 
username table. 

Syntax 

show snmp user 

Description 

The  show  snmp  user  command  displays 
information  about  each  SNMP  username  in 
the SNMP group username table. 

Parameters 

None. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

 

Example Usage:

 

To display the SNMP users currently configured on the switch: 

DES-3326SR:4#show snmp user 
Command: show snmp user 
 
 Username        Group Name      SNMP Version Auth-Protocol 
PrivProtocol 
 --------------- --------------- ------------ ------------- ------------ 
 initial         initial         V3           None          None 
 
Total Entries: 1 
 
DES-3326SR:4#

 

 
 
 
 
 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands