D-Link DES-3326SRM Page 276 Command Line Interface Reference Manual Download

Page: 276 / 354

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

276

RIP Commands

config rip tx_mode

Purpose

Used to configure RIP

’

s transmission mode.

Syntax

config rip [ipif <ipif_name>/all]} tx_mode
[disable/v1_only/v1_compatiable/v2_only]
authentication [enabled/disabled]
<password>]

Description

This command is used to configure RIP

’

transmission mode.

Parameters

<ipif_name>

−

The name of the IP interface.

all

−

Specifies all the IP interfaces on the

switch.
disable

−

Prevents the reception of RIP

packets.
v1_only

−

Specifies that only RIP v1 packets

will be accepted.
v2_only

−

Specifies that only RIP v2 packets

will be accepted.
v1_and_v2

−

Specifies that both RIP v1 and v2

packets will be accepted.
authentication [enabled/disabled]

−

Enables

or disables authentication for RIP on the
switch.
<password>

−

Allows the specification of a

case-sensitive password.

Restrictions

If  no  IP  interface  is  specified,  the  setting  is
applied  to  all  IP  interfaces.    The  default  is
disabled.    Only  administrator-level  users  can
issue this command.

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Search results

Summary of Contents for DES-3326SRM

Reviews:

Related manuals for DES-3326SRM

Brands by name

Popular brands

D-Link DES-3326SRM, Command Line Interface Reference Manual

Search results

Summary of Contents for DES-3326SRM

Reviews:

Related manuals for DES-3326SRM

Brands by name

Popular brands