D-Link DES-3326SRM Command Line Interface Reference Manual Download | Manualshive

Page: 227 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Route Redistribution Commands

227

config route redistribute dst ospf

redistributed.

Parameters

src

−

Allows the selection of the protocol of

the source device.

dst

−

Allows the selection of the protocol of

the destination device.

mettype

−

allows the selection of one of the

methods  for  calculating  the  metric  value.
Type-a  calculates  the  metric  (for  RIP  to
OSPF)  by  adding  the  destination

’

s interface

cost to the metric entered in the Metric field.
Type-2 uses the metric entered in the Metric
field without change. This field applies only
when the destination field is OSPF.

metric <value>

−

Allows the entry of an

OSPF interface cost. This is analogous to a
Hop Count in the RIP routing protocol.

Restrictions

Only administrator-level users can issue
this command.

Routing information source

−

RIP: the Static Route table, and the

Local interface routing information. Routing information will be
redistributed to OSPF. The following table lists the allowed values
for the routing metrics and the types (or forms) of the routing
information that will be redistributed.

«
...
225
226
227
228
229
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

SmartSwitch 9A100

Brand: Cabletron Systems Pages: 52

SmartSwitch 9W006

Brand: Cabletron Systems Pages: 34

SmartSTACK ELS100-S24TX2M

Brand: Cabletron Systems Pages: 102

Brand: Cabletron Systems Pages: 24

SmartSwitch 9000

Brand: Cabletron Systems Pages: 14

Brand: Cabletron Systems Pages: 38

Brand: Datavideo Pages: 2

Brand: FANATEC Pages: 40

Brand: Harman Kardon Pages: 2

8271 Nways Ethernet LAN Switch

Brand: IBM Pages: 210

Brand: IDEC Pages: 8

Brand: IDEM SAFETY SWITCHES Pages: 2

Brand: SMC Networks Pages: 102

EdgeSwitch 10 XP

Brand: Ubiquiti Pages: 13

MatrixPRO 8x8 DVI

Brand: Barco Pages: 2

Brand: Aastra Pages: 52

Brand: Xunison Pages: 14

Brand: H3C Pages: 57

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands