manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

DVMRP Commands 

281 

 

27 

DVMRP C

OMMANDS

 

The  switch  port  commands  in  the  Command  Line  Interface  (CLI) 
are listed (along with the appropriate parameters) in the following 
table. 

 

Command 

Parameters 

config dvmrp 

ipif <ipif_name> 
all 
metric <value> 
probe <sec> 
neighbor_timeout <sec> 
state [enabled/disabled] 

enable dvmrp 

 

disable dvmrp 

 

show dvmrp 
routing_table 

ipaddress <network_address> 

show dvmrp 
neighbor 

ipif <ipif_name> 
ipaddress <network_address> 

show dvmrp 
nexthop 

ipaddress <network_address> 

show dvmrp 

ipif <ipif_name> 

 

Each command is listed, in detail, in the following sections. 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

ABB eOT Series Installation Instructions Manual preview
eOT Series
Brand: ABB Pages: 10
AMX AVS-OP-1616-340 Product View preview
AVS-OP-1616-340
Brand: AMX Pages: 1
INFLUX MEASUREMENTS SPDB 30 Manual To The Installation, Operation & Maintenance preview
SPDB 30
Brand: INFLUX MEASUREMENTS Pages: 6
CyberData 4-Port PoweredUSB 2.0 Hub 011006 Quick Reference Manual preview
4-Port PoweredUSB 2.0 Hub 011006
Brand: CyberData Pages: 4
Enterasys Matrix DFE-Gold 4G4202-60 Hardware Installation Manual preview
Matrix DFE-Gold 4G4202-60
Brand: Enterasys Pages: 78
ZENEC 2E-AVS Instruction Manual preview
2E-AVS
Brand: ZENEC Pages: 16
Kramer Sierra Video 1208V3S Specifications preview
Sierra Video 1208V3S
Brand: Kramer Pages: 2
Eaton Edison Cooper Power Series Installation And Operation Instructions Manual preview
Edison Cooper Power Series
Brand: Eaton Pages: 12
N-Tron 709FX Series User Manual & Installation Manual preview
709FX Series
Brand: N-Tron Pages: 196
Quintech RFS 0702 Operation And Adjustment Procedure preview
RFS 0702
Brand: Quintech Pages: 2
N-Tron 302MC-XX Installation Manual preview
302MC-XX
Brand: N-Tron Pages: 16
Gefen ToolBox GTB-MHDMI1.3-441 User Manual preview
ToolBox GTB-MHDMI1.3-441
Brand: Gefen Pages: 25
PRO SIGNAL PSG3061 Quick Start Manual preview
PSG3061
Brand: PRO SIGNAL Pages: 4
Scion SC03.4101 Operation Manual preview
SC03.4101
Brand: Scion Pages: 8
H3C S6812 Series Installation Manual preview
S6812 Series
Brand: H3C Pages: 77
AMX AVS-OCT-3264-360 Product View preview
AVS-OCT-3264-360
Brand: AMX Pages: 1
Optone OPT-6016 Manual preview
OPT-6016
Brand: Optone Pages: 10
Hailink MX44NN00RK User Manual preview
MX44NN00RK
Brand: Hailink Pages: 6

Brands by name

Popular brands

Load more brands