manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

74

 

Network Management Commands 

 

config snmp engineID 

Purpose 

Used to configure a name for the SNMP 
engine on the switch. 

Syntax 

config snmp engineID <snmp_engineID> 

Description 

The config snmp engineID command 
configures a name for the SNMP engine on 
the switch. 

Parameters 

<snmp_engineID> 

−

 An alphanumeric string 

that will be used to identify the SNMP 
engine on the switch. 

Restrictions 

Only administrator-level users can issue 
this command. 

 

Example Usage:

 

To give the SNMP agent on the switch the name 

“

0035636666

”

 

DES-3326SR:4#config snmp 0035636666  
Command: config snmp engineID 0035636666 
 
 Success. 
 
DES-3326SR:4# 

 
 
 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Magnetrol TK1 Operating Manual preview
TK1
Brand: Magnetrol Pages: 12
Magnimage V4 Series User Manual preview
V4 Series
Brand: Magnimage Pages: 53
Hall Technologies EMCEE200 User Manual preview
EMCEE200
Brand: Hall Technologies Pages: 35
Greengate VNLW-P-1001-MV-N-V Installation Instructions preview
VNLW-P-1001-MV-N-V
Brand: Greengate Pages: 2
Key Digital HD Flash 4 KD-SW4x1 Operating Instructions Manual preview
HD Flash 4 KD-SW4x1
Brand: Key Digital Pages: 12
DANLERS EZ CESR Installation Notes preview
EZ CESR
Brand: DANLERS Pages: 2
Festo SOEL-RTH-Q20 Manual preview
SOEL-RTH-Q20
Brand: Festo Pages: 2
KinAn DPU102 User Manual preview
DPU102
Brand: KinAn Pages: 4
steute Ex 355 Mounting And Wiring Instructions preview
Ex 355
Brand: steute Pages: 20
3onedata IES6200-PN-16T4GS-2P48 Quick Installation Manual preview
IES6200-PN-16T4GS-2P48
Brand: 3onedata Pages: 3
Milestone pro MP-SU21T-KVM User Manual preview
MP-SU21T-KVM
Brand: Milestone pro Pages: 32
Wetekom 83 52 59 Original Instruction Manual preview
83 52 59
Brand: Wetekom Pages: 34
Cypress SE-DVI-8-LC Operation Manual preview
SE-DVI-8-LC
Brand: Cypress Pages: 4
GarrettCom Ethernet Networks and Web Management Brochure preview
Ethernet Networks and Web Management
Brand: GarrettCom Pages: 12
Net Optics IBPO-HB50SR-XFP User Manual preview
IBPO-HB50SR-XFP
Brand: Net Optics Pages: 53
AT&T NetGate 8200 Installation Manual preview
NetGate 8200
Brand: AT&T Pages: 24
Wyrestorm MXV-0808-H2L Quick Start Manual preview
MXV-0808-H2L
Brand: Wyrestorm Pages: 2
ATEN CS62T User Manual preview
CS62T
Brand: ATEN Pages: 21

Brands by name

Popular brands

Load more brands