D-Link DES-3326SRM Page 117 Command Line Interface Reference Manual Download | Manualshive

Page: 117 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

Network Monitoring Commands

117

To create syslog host:

DES-3326SR:4#create syslog host 1 severity all facility local0

Command: create syslog host 1 severity all facility local0

Success.

DES-3326SR:4#

config syslog host

Purpose

Used to configure the syslog protocol to send
system log data to a remote host.

Syntax

config syslog host [all/<index 1-4>] {severity
[informational/warning/all]/
facility[local0/local1/local2/local3/
local4/local5/local6/local7]/udp_port<int>/
ipaddress <ipaddr>/ state[enabled/disabled]

Description

The config syslog host command is used to
configure the syslog protocol to send system log
information to a remote host.

Parameters

all

−

Specifies that the command will be applied

to all hosts.

<index 1-4>

−

Specifies that the command will

be applied to an index of hosts. There are four
available indexes, numbered 1 through 4.

severity

−

Severity level indicator.

These are described in the following:

Bold font indicates that the

«
...
115
116
117
118
119
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

WJSX150 - SWITCHER - ADDENDUM

Brand: Panasonic Pages: 48

Brand: KanexPro Pages: 16

Brand: F&F Pages: 10

Brand: Comm-Tec Pages: 48

Brand: Lightwave Pages: 53

Brand: NegoRack Pages: 41

IES2016-16T Series

Brand: 3onedata Pages: 3

OMNICUBE F1DK102P

Brand: Belkin Pages: 21

Brand: ATEN Pages: 2

Brand: Pakedge Device & Software Pages: 8

Brand: Black Box Pages: 2

5-Port Gigabit Switch 1000 Mbps

Brand: Hama Pages: 2

Brand: TDT Pages: 21

Brand: TRENDnet Pages: 2

Comfy LW920 Professional Series

Brand: LightwaveRF Pages: 41

Brand: Extron electronics Pages: 59

Brand: Rose electronics Pages: 68

Brand: PS Automation Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands