D-Link DES-3326SRM Command Line Interface Reference Manual Download | Manualshive

Page: 54 / 354

background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual

54

Network Management Commands

6

N

ETWORK

M

ANAGEMENT

C

OMMANDS

The network management commands in the Command Line
Interface (CLI) are listed (along with the appropriate parameters)
in the following table.

The  DES-3326SR  supports  the  Simple  Network  Management
Protocol  (SNMP)  versions  1,  2c,  and  3.    You  can  specifiy  which
version of the SNMP  you  want  to  use  to  monitor  and  control  the
switch.    The  three  versions  of  SNMP  vary  in  the  level  of  security
provided between the management station and the network device.
The  following  table  lists  the  security  features  of  the  three  SNMP
versions:

SNMP
Version

Authentication
Method

Description

v1

Community String

Community String is used for
authentication

−

NoAuthNoPriv

v2c

Community String

Community String is used for
authentication

−

NoAuthNoPriv

v3

Username

Username is used for
authentication

−

NoAuthNoPriv

v3

MD5 or SHA

Authentication is based on the
HMAC-MD5 or HMAC-SHA
algorithms

−

AuthNoPriv

v3

MD5 DES or SHA
DES

Authentication is based on the
HMAC-MD5 or HMAC-SHA
algorithms

−

AuthPriv.

DES 56-bit encryption is added
based on the CBC-DES (DES-56)
standard

«
...
52
53
54
55
56
...
»

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

Brand: NETGEAR Pages: 15

SilverStorm 9000

Brand: Qlogic Pages: 50

Brand: Hansen Pages: 4

Anaconda Switcher VK68A

Brand: X10 Pages: 2

Brand: Paugge Pages: 20

FortiSwitch 424E Series

Brand: Fortinet Pages: 11

Brand: Scame electrical solutions Pages: 68

Tek-CARE NC554/8

Brand: TekTone Pages: 2

Brand: MicroNet Pages: 123

Mini Hub 5 port

Brand: Sandberg Pages: 12

Brand: Leviton Pages: 2

Brand: LevelOne Pages: 40

Brand: D+H Pages: 16

Brand: Fastcabling Pages: 4

Brand: IOGear Pages: 6

Brand: Netis Pages: 8

Brand: NEOiD Pages: 44

Stackable MiniHub Le2801a

Brand: Black Box Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands