manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

Share
Download
D-Link DES-3326SRM Command Line Interface Reference Manual Download Page 294

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

294

 

IP Multicasting Commands 

 

Usage Example: 

 

To display the current IP multicast forwarding cache: 

DES-3326SR:4#show ipmc cache 
Command: show ipmc cache 
Multicast Group  Source IP Addr.   Source Mask   Upstream        
Expire   Prot. 
                                                                                    Neighbor         
Time 
------------------  -----------------                  ---------------          -----------      -----
----  --------- 
224.1.1.1         10.48.74.121                255.0.0.0           10.48.75.63     30     
dvmrp 
224.1.1.1           20.48.74.25               255.0.0.0            20.48.75.25     20    
pim-dm    
224.1.2.3             10.48.75.3               255.0.0.0           10.48.76.6        30     
dvmrp 
 
Total Entries: 3 
 
DES-3326SR:4#

 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands