manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

RIP Commands 

279 

 

 

disable rip 

Purpose 

Used to disable RIP. 

Syntax 

disable rip 

Description 

This  command  is  used,  along  with  the 
enable  RIP  command  below,  to  enable  or 
disable RIP on the switch. 

Parameters 

none. 

Restrictions 

Only  administrator-level  users  can  issue 
this command. 

 

Example Usage: 

To disable rip. 

 

DES-3326SR:4#disable rip 
Command: disable rip 
 

Success. 

 

DES-3326SR:4# 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

D-Link DGS-1024D - Switch Quick Installation Manual preview
DGS-1024D - Switch
Brand: D-Link Pages: 16
D-Link DGS-1016D - Switch User Manual preview
DGS-1016D - Switch
Brand: D-Link Pages: 44
D-Link DES-6000 Series Firmware Update Manual preview
DES-6000 Series
Brand: D-Link Pages: 3
D-Link DES-5024 - Switch Application Notes preview
DES-5024 - Switch
Brand: D-Link Pages: 2
D-Link DES-3828 - xStack Switch - Stackable Datasheet preview
DES-3828 - xStack Switch - Stackable
Brand: D-Link Pages: 3
D-Link DES-3550 User Manual preview
DES-3550
Brand: D-Link Pages: 192
D-Link DES-3326 Configuration Manual preview
DES-3326
Brand: D-Link Pages: 9
D-Link DES-3226L User Manual preview
DES-3226L
Brand: D-Link Pages: 110
D-Link DES-1026G User Manual preview
DES-1026G
Brand: D-Link Pages: 10
D-Link DES-1008D Manual preview
DES-1008D
Brand: D-Link Pages: 17
D-Link DES-1005P Quick Install Manual preview
DES-1005P
Brand: D-Link Pages: 4
D-Link DGS-1210-28P Manual preview
DGS-1210-28P
Brand: D-Link Pages: 9
D-Link DES-1024D Brochure preview
DES-1024D
Brand: D-Link Pages: 4
D-Link DGS-105 - Switch Datasheet preview
DGS-105 - Switch
Brand: D-Link Pages: 4
D-Link DES-1024D Quick Install Manual preview
DES-1024D
Brand: D-Link Pages: 2
D-Link des-1016a Quick Install Manual preview
des-1016a
Brand: D-Link Pages: 2
IDEC HS5L Series Instruction Sheet preview
HS5L Series
Brand: IDEC Pages: 8
IDEM SAFETY SWITCHES MPR Operating Instructions preview
MPR
Brand: IDEM SAFETY SWITCHES Pages: 2

Brands by name

Popular brands

Load more brands