manualshive.com logo in svg

D-Link DES-3326SRM, Command Line Interface Reference Manual

The D-Link DES-3326SRM product comes with a comprehensive Command Line Interface Reference Manual perfect for users seeking in-depth technical assistance. This manual provides crucial information for configuration and troubleshooting. Download the user manual for free from our website and unlock the full potential of your DES-3326SRM device.

Share
Download
background image

DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 

OSPF Configuration Commands 

327 

 

 

show ospf virtual neighbor 

Purpose 

Used  to  display  the  current  OSPF  virtual 
neighbor router table. 

Syntax 

show ospf virtual_neighbor {<area_id>} 

Description 

This command will display the current OSPF 
virtual neighbor router table. 

Parameters 

<area_id> 

−

  A  32-bit  number  in  the  form  of 

an 

IP 

address 

(xxx.xxx.xxx.xxx)  that 

uniquely  identifies  the  OSPF  area  in  the 
OSPF domain. 

<neighbor_id> 

−

 The OSPF router ID  for  the 

remote area.  This is a 32-bit number in the 
form  of  an  IP  address  (xxx.xxx.xxx.xxx)  that 
uniquely  identifies  the  remote  area

’

s  Area 

Border Router. 

Restrictions 

none. 

Usage Example 

 

To display the current OSPF virtual neighbor table: 

DES-3326SR:4#show ospf virtual_neighbor 
Command: show ospf virtual_neighbor 
 
Transit    Router ID of        IP Address of       Virtual Neighbor 
Area ID   Virtual Neighbor Virtual Neighbor  State 
--------------- ----------------     ----------------            ---------------- 
10.1.1.1      10.2.3.4            10.48.74.111          Exchange 
 
DES-3326SR:4# 

 

 

 

Summary of Contents for DES-3326SRM



































































































































































































































































































































































Reviews:

No comments

Related manuals for DES-3326SRM

UNICOM FEP-31024T-3 Specifications preview
FEP-31024T-3
Brand: UNICOM Pages: 1
Sams DS-4 User Manual For Use And Maintenance preview
DS-4
Brand: Sams Pages: 10
D-Link DXS-3410 Series Hardware Installation Manual preview
DXS-3410 Series
Brand: D-Link Pages: 54
rako WCM-D Instruction Manual preview
WCM-D
Brand: rako Pages: 4
DAITEM SA706AX Installation Manual preview
SA706AX
Brand: DAITEM Pages: 37
Intermatic T1906 Supplementary Manual preview
T1906
Brand: Intermatic Pages: 1
Ruby Tech Web-Smart GS-1208M Specifications preview
Web-Smart GS-1208M
Brand: Ruby Tech Pages: 2
Nextech XC5906 Instruction Manual preview
XC5906
Brand: Nextech Pages: 4
Harman AMX PR01-0808 User Manual preview
AMX PR01-0808
Brand: Harman Pages: 50
Tabs TBGW100-915 Reference Manual preview
TBGW100-915
Brand: Tabs Pages: 4
DANLERS CEFLA PIR DALIP Installation Notes preview
CEFLA PIR DALIP
Brand: DANLERS Pages: 2
B&B Electronics UHR304 Quick Start Manual preview
UHR304
Brand: B&B Electronics Pages: 2
Linksys EG008W - Instant Gigabit Workgroup Switch User Manual preview
EG008W - Instant Gigabit Workgroup Switch
Brand: Linksys Pages: 27
SICK 8026014 Operating Instructions Manual preview
8026014
Brand: SICK Pages: 64
AMX Solecis AVS-SL-PR-0201-0301 Operation/Reference Manual preview
Solecis AVS-SL-PR-0201-0301
Brand: AMX Pages: 24
PCB Piezotronics IMI SENSORS EX686B01 Installation And Operating Manual preview
IMI SENSORS EX686B01
Brand: PCB Piezotronics Pages: 59
AMERITRON RCS-12 Instruction Manual preview
RCS-12
Brand: AMERITRON Pages: 16
Honeywell Home 50027910-001 Installation Instructions preview
50027910-001
Brand: Honeywell Home Pages: 4

Brands by name

Popular brands

Load more brands